搜索

x

留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

纳米颗粒的表面效应和电极颗粒间挤压作用对锂离子电池电压迟滞的影响

彭劼扬 王家海 沈斌 李浩亮 孙昊明

引用本文:
Citation:

纳米颗粒的表面效应和电极颗粒间挤压作用对锂离子电池电压迟滞的影响

彭劼扬, 王家海, 沈斌, 李浩亮, 孙昊明

Influences of nanoscale particles and interparticle compression in electrodes on voltage hysteresis of lithium ion batteries

Peng Jie-Yang, Wang Jia-Hai, Shen Bin, Li Hao-Liang, Sun Hao-Ming
PDF
HTML
导出引用
  • 硅作为锂离子电池电极材料之一, 其应力效应尤为突出, 进而将影响电池性能. 本文建立了电化学反应-扩散-应力全耦合模型, 并研究了恒压充放电条件下扩散诱导应力、表面效应和颗粒间挤压作用对电压迟滞的影响. 结果发现, 应力及其导致的电压迟滞程度与颗粒尺寸相关. 在大颗粒(颗粒半径r > 100 nm)中, 扩散诱导应力是导致电势迟滞效应的主要因素, 这将导致电池能量耗散. 对于纳米级小颗粒(r < 100 nm)而言, 表面效应占据主导, 表面效应虽然能缓解电压迟滞, 同时却会使驱动电化学反应部分的过电势回线下移, 造成锂化容量衰减. 本文综合考虑了扩散诱导应力和表面效应, 得出: 半径为10 nm的颗粒将会使电极具备较好的综合性能. 此外, 对于硅电极而言, 颗粒间挤压作用会使应力回线向压应力状态演化, 进而导致锂化容量的衰减. 计算结果表明, 在电极设计中, 对孔隙率设定下限值有助于提升电极性能.
    As one of high capacity electrode materials of lithium ion battery, silicon suffers significant stress effects, which further affects the voltage performance of battery. In this paper, a reaction-diffusion-stress coupled model is established, and the stress induced voltage hysteresis with consideration of diffusion induced stress, surface effects and interparticle compression under potentiostatic operation are investigated. It is found that stress and stress induced voltage hysteresis are dependent on particle size. For big particles, the diffusion induced stress is dominant and further aggravates the hysteresis of both stress and the overpotential consumed by it, indicating that more energy dissipates due to the stress effects. For small particles, especially ones with radius of a few nanometers, surface effects play a more prominent role than diffusion induced stress and the stress evolves into the state of compressive stress on the whole, leading the hysteresis of overpotential to be consumed by stress shrink and making the hysteresis plot of overpotential used to drive electrochemical reaction move downward. The electrode potential first reaches a cutoff voltage and finally the capacity of lithium ion battery decays. Therefore, too large or too small particle size in the electrode can both have a negative effect on the performance of lithium ion batteries, which indicates that an optimal size of the electrode particles must be designed in terms of electrode structure. Based on the calculation, particles with around 9 nm in radius are an appropriate option for electrode design in consideration of both diffusion induced stress and surface effect. In addition, for silicon electrodes, the silicon particles inevitably squeeze each other in a charge and discharge cycle. Therefore, interparticle compression is considered in this case. In detail, interparticle compression pushes the plot of stress hysteresis to the compressive state and leads to lower lithiation capacity, which makes the overpotential plot consumed by stress move downward and accordingly the overpotential plot used to drive the electrochemical reaction move upward. Denser electrode would strengthen this effect due to higher particle compression. It is indicated that for electrode design, the minimum of porosity ratio of electrodes should be adopted because higher interparticle compressive stress would reduce the battery capacity. Our results reveal that the voltage hysteresis of lithium ion batteries is related to the active particle size and the porosity ratio of the electrode, which is of great significance for guiding one in designing the lithium ion batteries.
      通信作者: 李浩亮, wuwangchuxin@shu.edu.cn
    • 基金项目: 国家重点研发计划(批准号: 2017YFE0101400)资助的课题.
      Corresponding author: Li Hao-Liang, wuwangchuxin@shu.edu.cn
    • Funds: Project supported by the National Key R&D Program of China (Grant No. 2017YFE0101400).
    [1]

    Konishi H, Hirano T, Takamatsu D, Gunji A, Feng X L, Furutsuki S 2015 J. Power Sources 298 144Google Scholar

    [2]

    Shi S Q, Gao J, Liu Y, Zhao Y, Wu Q, Ju W W, Ouyang C Y, Xiao R J 2016 Chin. Phys. B. 25 18212Google Scholar

    [3]

    Yang L, Chen H S, Jiang H Q, Wei Y J, Song W L, Fang D N 2018 Chem. Commun. 54 3997Google Scholar

    [4]

    McDowell M T, Ryu L, Lee S W, Wang C, Nix W D, Cui Y 2012 Adv. Mater. 24 6034Google Scholar

    [5]

    Liu X H, Fan F F, Yang H, Zhang S, Huang J Y, Zhu T 2013 ACS Nano. 7 1495

    [6]

    Gu M, Yang H, Perea D E, Zhang J G, Zhang S, Wang C M 2014 Nano Lett. 14 4622Google Scholar

    [7]

    Kim S, Choi S J, Zhao K J, Yang H, Gobbi G, Zhang S, Li J 2016 Nat. Commun. 7 10146Google Scholar

    [8]

    Piper D M, Yersak T A, Lee S H 2013 J. Electrochem. Soc. 160 A77Google Scholar

    [9]

    Sethuraman V A, Chon M J, Shimshak M, Srinivasan V, Guduru P R 2010 J. Power Sources 195 5062Google Scholar

    [10]

    Bower A F, Guduru P R, Sethuraman V A 2011 J. Mech. Phys. Solids 59 804Google Scholar

    [11]

    Sethuraman V A, Srinivasan V, Bower A F, Guduru P R 2010 J. Electrochem. Soc. 157 A1253Google Scholar

    [12]

    Lu B, Song Y C, Zhang Q L, Pan J, Cheng Y T, Zhang J Q 2016 Phys. Chem. Chem. Phys. 18 4721Google Scholar

    [13]

    Song Y C, Soh A K, Zhang J Q 2016 J. Mater. Sci. 51 9902Google Scholar

    [14]

    Magasinski A, Dixon P, Hertzberg B, Kvit A, Ayala J, Yushin G 2010 Nat. Mater. 9 353Google Scholar

    [15]

    Meng Q P, Wu L J, Welch D O, Tang M, Zhu Y M 2018 Sci. Rep. 8 4396Google Scholar

    [16]

    Cheng Y T, Verbrugge M W 2008 J. Appl. Phys. 104 083521Google Scholar

    [17]

    Hao F, Gao Z, Fang D N 2012 J. Appl. Phys. 112 103507Google Scholar

    [18]

    Haftbaradaran H, Song J, Curtin W A, Gao H J 2011 J. Power Sources 196 361Google Scholar

    [19]

    Sethuraman V A, Srinivasan V, Newman J 2013 J. Electrochem. Soc. 160 A394Google Scholar

    [20]

    Cheng Y T, Verbrugge M W 2009 J. Power Sources 190 453Google Scholar

    [21]

    Stein P, Zhao Y, Xu B X 2016 J. Power Sources 332 154Google Scholar

    [22]

    Gibbs J W 1906 The Scientific Papers of J. Willard Gibbs (London: Longmans, Green and Company)

    [23]

    Cammarata R C 1994 Prog. Surf. Sci. 46 1

    [24]

    Müller P, Saúl A 2004 Surf. Sci. Rep. 54 157Google Scholar

    [25]

    Rusanov A I 2005 Surf. Sci. Rep. 58 111

    [26]

    Fischer F D, Waitz T, VollathD, Simha N K 2008 Prog. Mater. Sci. 53 481Google Scholar

    [27]

    Gurtin M E, Murdoch A I 1975 Arch. Ration. Mech. An. 57 291Google Scholar

    [28]

    Gurtin M E, Murdoch A I 1978 Int. J. Solids Struct. 14 431Google Scholar

    [29]

    Gurtin M E, Weissmüller J, Larché F 1998 Philos. Mag. A 78 1093

    [30]

    Sharma P, Ganti S, Bhate N 2003 Appl. Phys. Lett. 82 535Google Scholar

    [31]

    Miller R E, Shenoy V B 2000 Nanotechnology 11 139Google Scholar

    [32]

    Luo L, Zhao P, Yang H, Liu B, Zhang J G, Cui Y, Wang C M 2015 Nano Lett. 15 7016Google Scholar

    [33]

    Bucci G, Swamy T, Bishop S, Sheldon B W, Chiang Y M, Carter W C 2017 J. Electrochem. Soc. 164 A645Google Scholar

    [34]

    Roberts A P, Garboczi E J 2000 J. Am. Ceram. Soc. 83 3041Google Scholar

    [35]

    Qi W, Shapter J G, Wu Q, Yin T, Gao G, Cui D 2017 J Mater Chem. A. 5 19521Google Scholar

    [36]

    Roy P, Srivastava S K 2015 J. Mater. Chem. A 3 2454Google Scholar

    [37]

    Vitos L, Ruban A V, Skriver H L 1998 Surf. Sci. 411 186Google Scholar

    [38]

    Yang B, He YP, Irsa J, Lundgren C A, Ratchford J B, Zhao Y P 2012 J. Power Sources 204 168Google Scholar

    [39]

    Gwak Y, Moon J, Cho M 2016 J. Power Sources 307 856Google Scholar

    [40]

    Ding N, Xu J, Yao Y X, Wegner G, Fang X, Chen C H, Lieberwirth 2009 Solid State Ionics 180 222Google Scholar

    [41]

    Ying Z, Peter S, Yang B, Mamun A S, Yangyiwei Y, Xua B X 2019 J. Power Sources 413 259Google Scholar

  • 图 1  锂离子电池中的多层电极结构

    Fig. 1.  Multi-scale hierarchical electrode structure in lithium ion battery.

    图 2  Sethuraman等[19]硅电极开路电势的拟合结果和实验结果, 其中红色的数据点是实验测得的锂化数据, 蓝色数据点是实验测得的去锂化数据, 实线是在C/8恒流充放电条件下的实验曲线, 虚线是依据实验数据拟合的结果

    Fig. 2.  Fitting results and experimental results of open-circuit potential of silicon electrode proposed by Sethuraman et al.[19]. The red data point is the lithium data measured in the experiment, and the blue data point is the dilithiated data measured in the experiment. The solid line was obtained under a C/8 constant current charge-discharge operation, and the dashed line is the fitting function

    图 3  扩散诱导应力对电压迟滞的影响 (a)电极颗粒在锂化和去锂化过程中锂离子的浓度分布; (b)一次充放电循环中, 不同尺寸的颗粒扩散诱导应力演化

    Fig. 3.  Effect of diffusion induced stress on voltage hysteresis: (a) Distribution of concentration of lithium ions in a electrode particle during lithiation and delithiation; (b) diffusion-induced stress evolution diagrams of particles with different sizes in primary charge-discharge cycle

    图 4  (a)−(d)分别是颗粒尺寸为10, 100, 400, 700 nm的各部分过电势演化图

    Fig. 4.  (a)−(d) Overpotential evolution charts of each part with particle size of 10, 100, 400, 700 nm, respectively

    图 5  应力分担过电势的差值、总过电势差值及其所占百分比在不同颗粒尺寸下的变化, 其中差值是指过电势回线中最大值与最小值之差

    Fig. 5.  Dependence of overpotential gap consumed by stress, total overpotential gap and the corresponding percentage on different particle sizes. The gap refers to the difference between the maximum value and the minimum value in the overpotential loop

    图 6  由表面效应引起的表面张力及其分担过电势的演化曲线, 其中黑色曲线的应力值为一次充放电循环中的平均应力值, 竖直曲线为各自的变化范围; 3张子图为对应的表面张力演化曲线

    Fig. 6.  Evolution curve of surface tension due to surface effect and the corresponding overpotential. The dark line represents the mean stress in a cycle and the bar defines the range. The three subplots are evolutions of surface stress due to surface effects in a cycle

    图 7  (a)不同颗粒尺寸下, 表面张力和扩散诱导应力共同作用下的表面静水应力演化图; (b), (c), (d), (e)分别是颗粒尺寸为4, 10, 100和400 nm时的各部分过电势演化图

    Fig. 7.  (a) Evolution of surface hydrostatic stresses in consideration of both diffusion induced stress and surface effects under different particle sizes; (b), (c), (d), (e) evolutions of all parts of overpotential in the particles of 4, 10, 100 and 400 nm radius, respectively

    图 8  不同颗粒尺寸下扩散诱导应力和表面效应引起的静水应力的绝对值对比

    Fig. 8.  Absolute values of the hydrostatic stress due to surface effects and the surface stress due to diffusion induced stress under different particle sizes.

    图 9  不同颗粒尺寸下扩散诱导应力与表面效应之和的演化

    Fig. 9.  Evolution diagram of the sum of diffusion induced stress and surface effect under different particle sizes

    图 10  颗粒间挤压对电压迟滞的影响 (a) 不同孔隙下电极的应力迟滞回线图; (b)−(e) 不同孔隙率下电极各部分过电势的回线图; 其中p为电池结构的孔隙率

    Fig. 10.  Impacts of interparticle compression on the voltage hysteresis: (a) Stress hysteresis for electrodes with different porosity ratios; (b)−(e) loop diagram of all parts of overpotential in the electrode with different porosity ratios. p is the porosity of the electrode structure.

    表 1  活性材料的材料参数[13,37-40]

    Table 1.  The material parameters of active materials[13,37-40]

    E/GPaνcmax/mol·m–3Ω/m3·molD/m2·s–1
    100[38]0.27[37]3.125 × 105[39]4.25 × 10–6[13]2 × 10–6[40]
    下载: 导出CSV
  • [1]

    Konishi H, Hirano T, Takamatsu D, Gunji A, Feng X L, Furutsuki S 2015 J. Power Sources 298 144Google Scholar

    [2]

    Shi S Q, Gao J, Liu Y, Zhao Y, Wu Q, Ju W W, Ouyang C Y, Xiao R J 2016 Chin. Phys. B. 25 18212Google Scholar

    [3]

    Yang L, Chen H S, Jiang H Q, Wei Y J, Song W L, Fang D N 2018 Chem. Commun. 54 3997Google Scholar

    [4]

    McDowell M T, Ryu L, Lee S W, Wang C, Nix W D, Cui Y 2012 Adv. Mater. 24 6034Google Scholar

    [5]

    Liu X H, Fan F F, Yang H, Zhang S, Huang J Y, Zhu T 2013 ACS Nano. 7 1495

    [6]

    Gu M, Yang H, Perea D E, Zhang J G, Zhang S, Wang C M 2014 Nano Lett. 14 4622Google Scholar

    [7]

    Kim S, Choi S J, Zhao K J, Yang H, Gobbi G, Zhang S, Li J 2016 Nat. Commun. 7 10146Google Scholar

    [8]

    Piper D M, Yersak T A, Lee S H 2013 J. Electrochem. Soc. 160 A77Google Scholar

    [9]

    Sethuraman V A, Chon M J, Shimshak M, Srinivasan V, Guduru P R 2010 J. Power Sources 195 5062Google Scholar

    [10]

    Bower A F, Guduru P R, Sethuraman V A 2011 J. Mech. Phys. Solids 59 804Google Scholar

    [11]

    Sethuraman V A, Srinivasan V, Bower A F, Guduru P R 2010 J. Electrochem. Soc. 157 A1253Google Scholar

    [12]

    Lu B, Song Y C, Zhang Q L, Pan J, Cheng Y T, Zhang J Q 2016 Phys. Chem. Chem. Phys. 18 4721Google Scholar

    [13]

    Song Y C, Soh A K, Zhang J Q 2016 J. Mater. Sci. 51 9902Google Scholar

    [14]

    Magasinski A, Dixon P, Hertzberg B, Kvit A, Ayala J, Yushin G 2010 Nat. Mater. 9 353Google Scholar

    [15]

    Meng Q P, Wu L J, Welch D O, Tang M, Zhu Y M 2018 Sci. Rep. 8 4396Google Scholar

    [16]

    Cheng Y T, Verbrugge M W 2008 J. Appl. Phys. 104 083521Google Scholar

    [17]

    Hao F, Gao Z, Fang D N 2012 J. Appl. Phys. 112 103507Google Scholar

    [18]

    Haftbaradaran H, Song J, Curtin W A, Gao H J 2011 J. Power Sources 196 361Google Scholar

    [19]

    Sethuraman V A, Srinivasan V, Newman J 2013 J. Electrochem. Soc. 160 A394Google Scholar

    [20]

    Cheng Y T, Verbrugge M W 2009 J. Power Sources 190 453Google Scholar

    [21]

    Stein P, Zhao Y, Xu B X 2016 J. Power Sources 332 154Google Scholar

    [22]

    Gibbs J W 1906 The Scientific Papers of J. Willard Gibbs (London: Longmans, Green and Company)

    [23]

    Cammarata R C 1994 Prog. Surf. Sci. 46 1

    [24]

    Müller P, Saúl A 2004 Surf. Sci. Rep. 54 157Google Scholar

    [25]

    Rusanov A I 2005 Surf. Sci. Rep. 58 111

    [26]

    Fischer F D, Waitz T, VollathD, Simha N K 2008 Prog. Mater. Sci. 53 481Google Scholar

    [27]

    Gurtin M E, Murdoch A I 1975 Arch. Ration. Mech. An. 57 291Google Scholar

    [28]

    Gurtin M E, Murdoch A I 1978 Int. J. Solids Struct. 14 431Google Scholar

    [29]

    Gurtin M E, Weissmüller J, Larché F 1998 Philos. Mag. A 78 1093

    [30]

    Sharma P, Ganti S, Bhate N 2003 Appl. Phys. Lett. 82 535Google Scholar

    [31]

    Miller R E, Shenoy V B 2000 Nanotechnology 11 139Google Scholar

    [32]

    Luo L, Zhao P, Yang H, Liu B, Zhang J G, Cui Y, Wang C M 2015 Nano Lett. 15 7016Google Scholar

    [33]

    Bucci G, Swamy T, Bishop S, Sheldon B W, Chiang Y M, Carter W C 2017 J. Electrochem. Soc. 164 A645Google Scholar

    [34]

    Roberts A P, Garboczi E J 2000 J. Am. Ceram. Soc. 83 3041Google Scholar

    [35]

    Qi W, Shapter J G, Wu Q, Yin T, Gao G, Cui D 2017 J Mater Chem. A. 5 19521Google Scholar

    [36]

    Roy P, Srivastava S K 2015 J. Mater. Chem. A 3 2454Google Scholar

    [37]

    Vitos L, Ruban A V, Skriver H L 1998 Surf. Sci. 411 186Google Scholar

    [38]

    Yang B, He YP, Irsa J, Lundgren C A, Ratchford J B, Zhao Y P 2012 J. Power Sources 204 168Google Scholar

    [39]

    Gwak Y, Moon J, Cho M 2016 J. Power Sources 307 856Google Scholar

    [40]

    Ding N, Xu J, Yao Y X, Wegner G, Fang X, Chen C H, Lieberwirth 2009 Solid State Ionics 180 222Google Scholar

    [41]

    Ying Z, Peter S, Yang B, Mamun A S, Yangyiwei Y, Xua B X 2019 J. Power Sources 413 259Google Scholar

  • [1] 谢奕展, 程夕明. 一种求解锂离子电池单粒子模型液相扩散方程的新方法. 物理学报, 2022, 71(4): 048201. doi: 10.7498/aps.71.20211619
    [2] 尚帅朋, 陆勇俊, 王峰会. 表面效应对纳米线电极屈曲失稳的影响. 物理学报, 2022, 71(3): 033101. doi: 10.7498/aps.71.20211864
    [3] 柳小伟, 宋辉, 郭美卿, 王根伟, 迟青卓. 基于电化学-应力耦合模型的锂离子电池硅/碳核壳结构的模拟与优化. 物理学报, 2021, 70(17): 178201. doi: 10.7498/aps.70.20210455
    [4] 谢奕展, 程夕明. 一种求解锂离子电池单粒子模型液相扩散方程的新方法. 物理学报, 2021, (): . doi: 10.7498/aps.70.20211619
    [5] 李涛, 程夕明, 胡晨华. 锂离子电池电化学降阶模型性能对比. 物理学报, 2021, 70(13): 138801. doi: 10.7498/aps.70.20201894
    [6] 梁晋洁, 高宁, 李玉红. 表面效应对铁${\left\langle 100 \right\rangle} $间隙型位错环的影响. 物理学报, 2020, 69(3): 036101. doi: 10.7498/aps.69.20191379
    [7] 曾建邦, 郭雪莹, 刘立超, 沈祖英, 单丰武, 罗玉峰. 基于电化学-热耦合模型研究隔膜孔隙结构对锂离子电池性能的影响机制. 物理学报, 2019, 68(1): 018201. doi: 10.7498/aps.68.20181726
    [8] 宋旭, 陆勇俊, 石明亮, 赵翔, 王峰会. 集流体塑性变形对锂离子电池双层电极中锂扩散和应力的影响. 物理学报, 2018, 67(14): 140201. doi: 10.7498/aps.67.20180148
    [9] 庞辉. 基于扩展单粒子模型的锂离子电池参数识别策略. 物理学报, 2018, 67(5): 058201. doi: 10.7498/aps.67.20172171
    [10] 庞辉. 基于电化学模型的锂离子电池多尺度建模及其简化方法. 物理学报, 2017, 66(23): 238801. doi: 10.7498/aps.66.238801
    [11] 彭颖吒, 张锴, 郑百林, 李泳. 广义平面应变锂离子电池柱形梯度材料颗粒电极中扩散诱导应力分析. 物理学报, 2016, 65(10): 100201. doi: 10.7498/aps.65.100201
    [12] 黄亮, 李建远. 基于单粒子模型与偏微分方程的锂离子电池建模与故障监测. 物理学报, 2015, 64(10): 108202. doi: 10.7498/aps.64.108202
    [13] 马昊, 刘磊, 路雪森, 刘素平, 师建英. 锂离子电池正极材料Li2FeSiO4的电子结构与输运特性. 物理学报, 2015, 64(24): 248201. doi: 10.7498/aps.64.248201
    [14] 李娟, 汝强, 孙大伟, 张贝贝, 胡社军, 侯贤华. 锂离子电池SnSb/MCMB核壳结构负极材料嵌锂性能研究. 物理学报, 2013, 62(9): 098201. doi: 10.7498/aps.62.098201
    [15] 黄乐旭, 陈远富, 李萍剑, 黄然, 贺加瑞, 王泽高, 郝昕, 刘竞博, 张万里, 李言荣. 氧化石墨制备温度对石墨烯结构及其锂离子电池性能的影响. 物理学报, 2012, 61(15): 156103. doi: 10.7498/aps.61.156103
    [16] 彭薇, 岳敏, 梁奇, 胡社军, 侯贤华. 锂离子电池LiMn1-xFexPO4(0x<1)正极材料的制备及性能研究. 物理学报, 2011, 60(3): 038202. doi: 10.7498/aps.60.038202
    [17] 白莹, 王蓓, 张伟风. 熔融盐法合成锂离子电池正极材料纳米LiNiO2. 物理学报, 2011, 60(6): 068202. doi: 10.7498/aps.60.068202
    [18] 侯贤华, 余洪文, 胡社军. 锂离子电池Sn-Al薄膜电极的制备及电化学性能研究. 物理学报, 2010, 59(11): 8226-8230. doi: 10.7498/aps.59.8226
    [19] 侯贤华, 胡社军, 石璐. 锂离子电池Sn-Ti合金负极材料的制备及性能研究. 物理学报, 2010, 59(3): 2109-2113. doi: 10.7498/aps.59.2109
    [20] 侯柱锋, 刘慧英, 朱梓忠, 黄美纯, 杨 勇. 锂离子电池负极材料CuSn的Li嵌入性质的研究. 物理学报, 2003, 52(4): 952-957. doi: 10.7498/aps.52.952
计量
  • 文章访问数:  9000
  • PDF下载量:  117
  • 被引次数: 0
出版历程
  • 收稿日期:  2018-12-29
  • 修回日期:  2019-02-25
  • 上网日期:  2019-05-01
  • 刊出日期:  2019-05-05

/

返回文章
返回