搜索

x

留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

液滴撞击液膜过程的格子Boltzmann方法模拟

黄虎 洪宁 梁宏 施保昌 柴振华

引用本文:
Citation:

液滴撞击液膜过程的格子Boltzmann方法模拟

黄虎, 洪宁, 梁宏, 施保昌, 柴振华

Lattice Boltzmann simulation of the droplet impact onto liquid film

Huang Hu, Hong Ning, Liang Hong, Shi Bao-Chang, Chai Zhen-Hua
PDF
导出引用
  • 本文采用格子Boltzmann方法对液滴撞击液膜过程进行了研究, 主要考察了雷诺数(Re)、韦伯数(We)、相对液膜厚度 (h) 以及表面张力 () 等物理参数对界面运动过程的影响. 首先, 随着Re数和We数的增加, 可以明显观察到液滴撞击液膜过程中形成的皇冠状水花以及卷吸现象; 当Re数较大时, 液体会发生飞溅, 由液体飞溅形成的小液滴则会继续下落, 并与液膜再次发生碰撞. 其次, 当相对液膜厚度较小时, 液滴撞击液膜并最终导致液膜断裂; 然而随着相对液膜厚度的增大, 尽管撞击过程溅起的液体会越来越多, 但是液膜并不会发生断裂. 再次, 随着表面张力的增大, 界面变形阻力增大, 撞击过程中产生的界面形变也逐渐减弱. 最后还发现皇冠(由液滴溅起形成)半径r 随时间满足r/(2R) Ut/(2R), 这一结果与已有结论是一致的.
    The process of the droplet impact onto the liquid film, as one of the basic multiphase problems, is very important in many fields of science and engineering. On the other hand, the problem is also very complicated since there are many parameters that may influence the process of the droplet impact on the liquid film. To clearly understand the physical phenomena appearing in the process droplet impact on the liquid film, a parametric study on this problem is conduced based on a recently developed lattice Boltzmann method in which a lattice Boltzmann model is used to solve the Navier-Stokes equations, and the other is adopted to solve the Cahn-Hilliard equation that is used to depict the interface between different phases. In this paper, we mainly focus on the effects of the Reynolds number (Re), the Weber number (We), the relative thickness of film (h) and the surface tension () on the dynamic behavior of interface between different phases, and the velocity and pressure fields are also presented. It is found that with the increase of Re and We, the phenomena of crown and entrainment can be observed obviously during the process of droplet impact onto the liquid film, and the radius of the crown seems not dependent on the We and Re where the relative thickness of film and surface tension are fixed to be 0.5 and 0.003. However, when Re becomes much larger, the splashing phenomenon is produced, and the small droplets caused by the splashing can fall and then impact onto the liquid film again. We also find that if the relative thickness of film is small, the surface tension, Re and We are set to be 0.003, 480 and 500, the film can break up during the process of the droplet impact onto the liquid film, while with the increase of relative thickness, although more liquid are induced in the splashing process, the film cant break up. In addition, with the increase of surface tension, the resistance which prevents the change of interface becomes large, and thus the change of interface is not large when the droplet impacts onto liquid film, as expected. And finally, a quantitative study on the relation between the radius of crown (formed by droplet impact onto liquid film) and the time is also performed, and the expression r/(2R) Ut/(2R) where the parameter is about 1.0 and is also independent of We and Re, can be used to describe the relation.
      通信作者: 柴振华, hustczh@hust.edu.cn
    • 基金项目: 国家自然科学基金(批准号: 51576079, 11272132)和湖北省自然科学基金(批准号: 2015CFB440)资助的课题.
      Corresponding author: Chai Zhen-Hua, hustczh@hust.edu.cn
    • Funds: Project supported by the National Natural Science Foundation of China (Grant Nos. 51576079, 11272132) and the National Natural Science Foundation of Hubei Province, China (Grant No. 2015CFB440).
    [1]

    Yarin A L 2006 Annu. Rev. Fluid Mech. 38 159

    [2]

    Rioboo R, Tropea C, Marengo M 2001 Atom. Sprays 11 155

    [3]

    Thoroddsen S T 2002 J. Fluid Mech. 451 373

    [4]

    Yarin A L, Weiss D A 1995 J. Fluid Mech. 382 141

    [5]

    Wang A B, Chen C C 2000 Phys. Fluids 12 2155

    [6]

    Mohamed-Kassim Z, Longmire E K 2003 Phys. Fluids 15 3263

    [7]

    Guo J H, Dai S Q, Dai Q 2010 Acta Phys. Sin. 59 2601 (in Chinese) [郭加宏, 戴世强, 代钦 2010 物理学报 59 2601]

    [8]

    Weiss D A, Yarin A L 1999 J. Fluid Mech. 385 229

    [9]

    Lee S H, Hur N, Kang S 2011 J. Mech. Sci. Tech. 25 2567

    [10]

    Xie H, Koshizuka S, Oka Y 2004 Int. J. Numer. Meth. Fluids 45 1009

    [11]

    Coppola G, Rocco G, Luca L D 2011 Phys. Fluids 23 0022105

    [12]

    Josseranda C, Zaleskib S 2003 Phys. Fluids 15 1650

    [13]

    Berberovi E, Hinsberg N P V, Jakirli S, Roisman I R, Tropea C 2009 Phys. Rev. E 79 036306

    [14]

    Liang G T, Guo Y L, Shen S Q 2013 Acta Phys. Sin. 62 024705 (in Chinese) [梁刚涛, 郭亚丽, 沈胜强 2013 物理学报 62 024705]

    [15]

    Wang Y, Shu C, Huang H B, Teo C J 2015 J. Comput. Phys. 280 404

    [16]

    Lee T, Lin C L 2005 J. Comput. Phys. 206 16

    [17]

    Li Q, Luo K H, Gao Y J, He Y L 2012 Phys. Rev. E 85 026704

    [18]

    Lee T, Liu L 2010 J. Comput. Phys. 229 8045

    [19]

    Rieber M, Frohn A 1999 Int. J. Heat Fluid Flow 20 445

    [20]

    Hai Q X, Zhong Z, Liang Q Z 2016 Chin. Phys. B 25 014702

    [21]

    Song B W, Ren F, Hu H B, Huang Q G 2015 Chin. Phys. B 24 014703

    [22]

    Chai Z H, Zhao T S 2012 Acta Mech. Sin. 28 983

    [23]

    Liang H, Shi B C, Guo Z L, Chai Z H 2014 Phys. Rev. E 89 053320

    [24]

    Huang J J, Huang H, Wang X 2015 Int. J. Numer. Meth. Fluids 77 123

  • [1]

    Yarin A L 2006 Annu. Rev. Fluid Mech. 38 159

    [2]

    Rioboo R, Tropea C, Marengo M 2001 Atom. Sprays 11 155

    [3]

    Thoroddsen S T 2002 J. Fluid Mech. 451 373

    [4]

    Yarin A L, Weiss D A 1995 J. Fluid Mech. 382 141

    [5]

    Wang A B, Chen C C 2000 Phys. Fluids 12 2155

    [6]

    Mohamed-Kassim Z, Longmire E K 2003 Phys. Fluids 15 3263

    [7]

    Guo J H, Dai S Q, Dai Q 2010 Acta Phys. Sin. 59 2601 (in Chinese) [郭加宏, 戴世强, 代钦 2010 物理学报 59 2601]

    [8]

    Weiss D A, Yarin A L 1999 J. Fluid Mech. 385 229

    [9]

    Lee S H, Hur N, Kang S 2011 J. Mech. Sci. Tech. 25 2567

    [10]

    Xie H, Koshizuka S, Oka Y 2004 Int. J. Numer. Meth. Fluids 45 1009

    [11]

    Coppola G, Rocco G, Luca L D 2011 Phys. Fluids 23 0022105

    [12]

    Josseranda C, Zaleskib S 2003 Phys. Fluids 15 1650

    [13]

    Berberovi E, Hinsberg N P V, Jakirli S, Roisman I R, Tropea C 2009 Phys. Rev. E 79 036306

    [14]

    Liang G T, Guo Y L, Shen S Q 2013 Acta Phys. Sin. 62 024705 (in Chinese) [梁刚涛, 郭亚丽, 沈胜强 2013 物理学报 62 024705]

    [15]

    Wang Y, Shu C, Huang H B, Teo C J 2015 J. Comput. Phys. 280 404

    [16]

    Lee T, Lin C L 2005 J. Comput. Phys. 206 16

    [17]

    Li Q, Luo K H, Gao Y J, He Y L 2012 Phys. Rev. E 85 026704

    [18]

    Lee T, Liu L 2010 J. Comput. Phys. 229 8045

    [19]

    Rieber M, Frohn A 1999 Int. J. Heat Fluid Flow 20 445

    [20]

    Hai Q X, Zhong Z, Liang Q Z 2016 Chin. Phys. B 25 014702

    [21]

    Song B W, Ren F, Hu H B, Huang Q G 2015 Chin. Phys. B 24 014703

    [22]

    Chai Z H, Zhao T S 2012 Acta Mech. Sin. 28 983

    [23]

    Liang H, Shi B C, Guo Z L, Chai Z H 2014 Phys. Rev. E 89 053320

    [24]

    Huang J J, Huang H, Wang X 2015 Int. J. Numer. Meth. Fluids 77 123

  • [1] 董攀, 田昌, 李杰, 王韬, 于海涛, 苏明旭, 何佳龙, 石金水. 基于Mie散射在线测量真空弧放电液滴方法探索. 物理学报, 2023, 72(8): 084203. doi: 10.7498/aps.72.20222406
    [2] 张晓林, 黄军杰. 楔形体上复合液滴润湿铺展行为的格子Boltzmann方法研究. 物理学报, 2023, 72(2): 024701. doi: 10.7498/aps.72.20221472
    [3] 彭家略, 郭浩, 尤天涯, 纪献兵, 徐进良. 液滴碰撞Janus颗粒球表面的行为特征. 物理学报, 2021, 70(4): 044701. doi: 10.7498/aps.70.20201358
    [4] 唐鹏博, 王关晴, 王路, 石中玉, 李源, 徐江荣. 单液滴正碰球面动态行为特性实验研究. 物理学报, 2020, 69(2): 024702. doi: 10.7498/aps.69.20191141
    [5] 魏衍举, 张洁, 邓胜才, 张亚杰, 杨亚晶, 刘圣华, 陈昊. 超声悬浮甲醇液滴的热诱导雾化现象. 物理学报, 2020, 69(18): 184702. doi: 10.7498/aps.69.20200562
    [6] 杨亚晶, 梅晨曦, 章旭东, 魏衍举, 刘圣华. 液滴撞击液膜的穿越模式及运动特性. 物理学报, 2019, 68(15): 156101. doi: 10.7498/aps.68.20190604
    [7] 梁宏, 柴振华, 施保昌. 分叉微通道内液滴动力学行为的格子Boltzmann方法模拟. 物理学报, 2016, 65(20): 204701. doi: 10.7498/aps.65.204701
    [8] 王松岭, 刘梅, 王思思, 吴正人. 随时间变化的非平整壁面对液膜表面波演化特性的影响. 物理学报, 2015, 64(1): 014701. doi: 10.7498/aps.64.014701
    [9] 郭亚丽, 魏兰, 沈胜强, 陈桂影. 双液滴撞击平面液膜的流动与传热特性. 物理学报, 2014, 63(9): 094702. doi: 10.7498/aps.63.094702
    [10] 张文彬, 廖龙光, 于同旭, 纪爱玲. 溶液液滴蒸发变干的环状沉积. 物理学报, 2013, 62(19): 196102. doi: 10.7498/aps.62.196102
    [11] 何峰, 王志军, 黄义辉, 叶鹏, 王锦程. 存在液膜的毛细蒸发过程研究. 物理学报, 2013, 62(24): 246401. doi: 10.7498/aps.62.246401
    [12] 梁刚涛, 郭亚丽, 沈胜强. 液滴撞击液膜的射流与水花形成机理分析. 物理学报, 2013, 62(2): 024705. doi: 10.7498/aps.62.024705
    [13] 苏铁熊, 马理强, 刘谋斌, 常建忠. 基于光滑粒子动力学方法的液滴冲击固壁面问题数值模拟. 物理学报, 2013, 62(6): 064702. doi: 10.7498/aps.62.064702
    [14] 刘邱祖, 寇子明, 韩振南, 高贵军. 基于格子Boltzmann方法的液滴沿固壁铺展动态过程模拟. 物理学报, 2013, 62(23): 234701. doi: 10.7498/aps.62.234701
    [15] 毕菲菲, 郭亚丽, 沈胜强, 陈觉先, 李熠桥. 液滴撞击固体表面铺展特性的实验研究. 物理学报, 2012, 61(18): 184702. doi: 10.7498/aps.61.184702
    [16] 张明焜, 陈硕, 尚智. 带凹槽的微通道中液滴运动数值模拟. 物理学报, 2012, 61(3): 034701. doi: 10.7498/aps.61.034701
    [17] 马理强, 常建忠, 刘汉涛, 刘谋斌. 液滴溅落问题的光滑粒子动力学模拟. 物理学报, 2012, 61(5): 054701. doi: 10.7498/aps.61.054701
    [18] 马理强, 刘谋斌, 常建忠, 苏铁熊, 刘汉涛. 液滴冲击液膜问题的光滑粒子动力学模拟. 物理学报, 2012, 61(24): 244701. doi: 10.7498/aps.61.244701
    [19] 郭加宏, 戴世强, 代钦. 液滴冲击液膜过程实验研究. 物理学报, 2010, 59(4): 2601-2609. doi: 10.7498/aps.59.2601
    [20] 石自媛, 胡国辉, 周哲玮. 润湿性梯度驱动液滴运动的格子Boltzmann模拟. 物理学报, 2010, 59(4): 2595-2600. doi: 10.7498/aps.59.2595
计量
  • 文章访问数:  6253
  • PDF下载量:  377
  • 被引次数: 0
出版历程
  • 收稿日期:  2015-11-23
  • 修回日期:  2015-12-28
  • 刊出日期:  2016-04-05

/

返回文章
返回