搜索

x

留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

SESRI 300 MeV同步加速器注入线的传输效率与接受效率

赵良超

引用本文:
Citation:

SESRI 300 MeV同步加速器注入线的传输效率与接受效率

赵良超

Transmission efficiency and beam reception of the SESRI 300 MeV synchrotron injection line

Zhao Liang-Chao
PDF
HTML
导出引用
  • 为了完成SESRI 300 MeV同步加速器的束流调试, 使用Tracewin软件和加速腔电磁场分布文件建立了该加速器注入线从离子源出口到注入点的全尺寸模型, 在多粒子模式下计算了两种典型粒子束(质子、209Bi32+)在不同状态下的加速传输, 得到了注入线上束流相空间的变化过程和注入线的传输效率与接受效率. 研究结果表明, 300 MeV同步加速器注入线在加速不同荷质比的离子束流时, 电磁场参数设置基本与荷质比成反比. 束流的接受效率主要由射频四极加速腔出口发射度决定. 质子束和重离子束的接受效率差别较大. 在射频四极加速腔出口发射度为0.1π mm·mrad时, 209Bi32+束接收效率达到92.13%, 质子束的接收效率为68.18%. 分析束流传输过程表明, 当横向发射度过大时, 束流会因为纵向能散展宽和相位展宽而无法被最终接受. 在现有配置下, 质子束存在横向聚焦力不够、接受效率较低的问题. 通过额外增加2个四极铁能够将质子束的接受效率由68.18%提升至83.61%.
    SESRI 300 MeV synchrotron in Harbin Institute of Technology is now under construction and the whole equipment has been installed and tested. Before commissioning beam, the beam transport through the injection line is simulated by using a full-scall model through the Tracewin code. The field distribution of RFQ cavity is calculated with CST, and the results are substituted into the Tracewin code to generate the accurate results. The envelop mode and multi-particles mode are used in the beam simulation with two typical beams (H${}_2^+ $ and 209Bi32+, the lightest beam and the heaviest beam). Both beams are accelerated from 4 keV/u to 2 MeV/u by an RFQ cavity and two IH-DTL cavities. Then the H${}_2^+ $ beam is stripped into a proton beam by a carbon foil and accelerated to 5.6 MeV with the third IH-DTL cavity. Simulation results show that the strength of the magnetic field and the acceleration field are proportional to the mass charge ratio. The beam transmission efficiency and the injection line reception are inversely proportional to the beam transverse emittance. The 209Bi32+ beam transmission efficiency and beam reception (momentum spread less than ±0.2%) are 72.16% and 46.72% with transverse emittance ε = 0.12π mm·mrad (ECR source output) and ε = 0.4π mm·mrad (RFQ output). H${}_2^+ $ beam transmission ratio and beam reception are 24.19% and 17.89% with ε = 0.2π mm·mrad (ECR source output) and ε = 0.5π mm·mrad (RFQ output). In order to obtain high transmission efficiency and beam reception, the transverse emittance should be limited to 0.1π mm·mrad after the RFQ. With this limitation, the 209Bi32+ beam transmission efficiency and the reception are increased to 96.68% and 92.63%, respectively, and the H${}_2^+ $ beam transmission efficiency and the rception rise to 74.40% and 68.18%, respectively. If two additional quadrupole magnets are added, the H${}_2^+ $ beam transmission efficiency and beam reception can be increased to 90.73% and 83.61%, respectively, which will fulfill the requirement for long-time operation. The phase space change process shows that loss of 209Bi32+ beam is caused mainly by longitudinal defocusing (energy spread and phase width spread), the loss of proton beam is caused both by the longitudinal defocusing and by the transverse defocusing (beam envelop spreading), that is why two additional focusing magnets should be added in proton beam acceleration. Results also show that by using field distribution calculation in the simulation process the greater influence of the cavity design details can be confirmed such as beam off-axis caused by dipole field in the IH-DTL cavity and beam loss caused by unperfect field in the RFQ. Tracking with field distribution is shown to be a useful method to link the cavity design process, beam line design process, and beam commission process.
      通信作者: 赵良超, zhaoliangchao@hit.edu.cn
    • 基金项目: 中央高校基本科研业务费专项资金(批准号: FRFCU5710053321)和国家自然科学基金青年基金(批准号: 12005208)资助的课题
      Corresponding author: Zhao Liang-Chao, zhaoliangchao@hit.edu.cn
    • Funds: Project supported by the Fundamental Research Funds for the Central Universities of Ministry of Education of China (Grant No. FRFCU5710053321) and the Young Scientists Fund of the National Natural Science Foundation of China (Grant No. 12005208)
    [1]

    Qian C, Sun L T, Jia Z H 2020 Rev. Sci. Instrum 91 023313Google Scholar

    [2]

    刘明 2017 硕士学位论文 (兰州: 近代物理研究所)

    Liu M 2017 M. S. Dissertation (Lanzhou: Institute of Modern Physics) (in Chinese)

    [3]

    喻九维, 杨雅清, 吕明邦, 陈文军, 郑亚军, 许小伟, 陆海娇, 潘永祥 2021 强激光与粒子束 33 054001

    Yu J W, Yang Y Q, Lü M B, Cheng W J, Zheng Y J, Xu X W, Lu H J, Pan Y X 2021 High Power Laser and Particle Beams 33 054001

    [4]

    李钟汕 2017 博士学位论文 (兰州: 近代物理研究所)

    Li Z S 2017 Ph. D. Dissertation (Lanzhou: Institute of Modern Physics) (in Chinese)

    [5]

    Ren H T, Pozdeyev E, Lund M S 2016 Rev. Sci. Instrum. 87 02B919Google Scholar

    [6]

    Akagi T, Bellan L 2020 Rev. Sci. Instrum. 91 023321Google Scholar

    [7]

    Clemente G, Ratzinger U, Podlech H, Groening L, Brodhage R, Barth W 2011 Phys. Rev. Spec. Top. Ac. 14 110101

    [8]

    Yang Y, Dou W P, Sun L T 2016 Rev. Sci. Instrum. 87 02B910Google Scholar

    [9]

    Thuillier T, Angot J, Barue C 2016 Rev. Sci. Instrum. 87 02A733Google Scholar

    [10]

    Benedetti S, Bellodi G, Kuchler D 2018 Rev. Sci. Instrum. 89 123301Google Scholar

    [11]

    Ullmann C, Berezov R, Fils J 2014 Rev. Sci. Instrum. 85 02A952Google Scholar

    [12]

    颜学庆, 陆元荣, 吴瑜, 张宏林, 高淑丽, 方家训 2002 北京大学学报 (自然科学版) 38 1

    Yan X Q, Lu Y R, Wu Y, Zhang H L, Gao S L, Fang J X 2002 Universitatis Pekinensis 38 1

    [13]

    吴瑜 1999 北京大学学报 (自然科学版) 35 3

    Wu Y 1999 Universitatis Pekinensis 35 3

    [14]

    王科栋 2019 博士学位论文 (兰州: 近代物理研究所)

    Wang K D 2017 Ph. D. Dissertation (Lanzhou: Institute of Modern Physics) (in Chinese)

    [15]

    Winklehner D, Hammond R, Alons J 2016 Rev. Sci. Instrum. 87 02B929Google Scholar

    [16]

    Otani M, Mibe T, Yoshida M 2016 Phys. Rev. Accel. Beams 19 040101Google Scholar

    [17]

    He T, Lu L, He Y, Hang Y L, Ma W, Tan T, Zhang Z L, Yang L, Xing C C, Li C X, Sun L P 2021 Nuclear Inst. Meth. Phys. Research A 1010 165466Google Scholar

    [18]

    Wang K D, Yuan Y J, Yin X J, Yang J C, Li Z S, Du H, Li X N, Kong Q Y, Wang K, Dong Z Q, Liu J, Xia J W 2019 Nuclear Inst. Meth. Phys. Research A 927 375Google Scholar

    [19]

    Uriot D 2003 Proceedings of the 2003 Particle Accelerator Conference, Portland, USA, May 12–16, 2003 p3491

    [20]

    吕建钦 2003 带电粒子束光学 (北京: 高等教育出版社) 第267页

    Lv J Q 2003 The Optics of Charged Particle Beams (Beijing: Higher Education Press) p267 (in Chinese)

    [21]

    陈佳洱 2019 加速器物理基础 (北京: 北京大学出版社) 第353页

    Chen J Er 2019 Foundment Physics of Accelerator (Beijing: Peking University Press) p353 (in Chinese)

  • 图 1  SESRI 300 MeV同步加速器注入线布局

    Fig. 1.  Injection line layout of SESRI 300 MeV synchrotron.

    图 2  RFQ结构及H${}_2^+ $束流加速

    Fig. 2.  RFQ structure and H${}_2^+ $ beam acceleration.

    图 3  IH-DTL加速腔结构及束流加速 (a) IH-DTL1加速H${}_2^+ $束; (b) IH-DTL2加速H${}_2^+ $束; (c) IH-DTL3加速质子束

    Fig. 3.  IH-DTL structure and beams acceleration: (a) H${}_2^+ $ beam acceleration in IH-DTL1; (b) H${}_2^+ $ beam acceleration in IH-DTL2; (c) proton beam acceleration in IH-DTL3.

    图 4  注入线第一段加速结构束流传输包络 (a) H$ {}_2^+ $束; (b) 209Bi32+

    Fig. 4.  Beam envelop in the first section of the injection line: (a) H$ {}_2^+ $ beam; (b) 209Bi32+ beam.

    图 5  注入线第一段RFQ出口处束流的六维相空间的分布 (a) H$ {}_2^+ $ 束; (b)209Bi32+

    Fig. 5.  Phase space distribution of the beam output by RFQ: (a) H$ {}_2^+ $ beam; (b) 209Bi32+ beam.

    图 6  注入线第二段加速结构束流传输包络 (a) H${}_2^+ $(剥离为质子)束; (b) 209Bi32+

    Fig. 6.  Beam envelop in the second section: (a) H${}_2^+ $(proton)beam; (b) 209Bi32+ beam.

    图 7  注入线出口处的束流相空间分布 (a) 质子束; (b) 209Bi32+

    Fig. 7.  Phase space distribution of the beam in front of septum: (a) Proton beam; (b) 209Bi32+ beam.

    图 8  209Bi32+在IH-DTL2出口处的纵向分布(灰色粒子为注入线最终接受的粒子) (a) ε = 0.1π mm·mrad; (b) ε = 0.4π mm·mrad

    Fig. 8.  Longitudinal distribution of 209Bi32+ beam output by IH-DTL2 (Gray particles are finally accepted by the injection line): (a) ε = 0.1π mm·mrad; (b) ε = 0.4π mm·mrad.

    图 9  增加四极磁铁前后质子束的包络(0.1π mm·mrad) (a)增加前; (b)增加后

    Fig. 9.  Proton beam envelop with and without additional quadrupoles (0.1π mm·mrad): (a) With additional quadrupoles; (b) without additional quadrupoles.

    图 10  增加四极磁铁前后质子束的β函数(0.1π mm·mrad) (a)增加前; (b)增加后

    Fig. 10.  β function of proton beam envelop with and without additional quadrupoles (0.1π mm·mrad): (a) Without additional quadrupoles; (b) with additional quadrupoles.

    表 1  注入线粒子束的指标

    Table 1.  Beam parameters of the injection line.

     指标要求
     粒子种类A/Q < 6.53的任意粒子
     能量重离子束2 MeV/u; 质子束5.6 MeV
     流强重离子束50e μA; 质子束250 μA
     90%自然发射度 < 15π mm·mrad
     Δp/p < ± 0.2%
    下载: 导出CSV

    表 2  RFQ输出束团横向发射度对注入线传输效率和接受效率的影响

    Table 2.  Transmission ratio and beam acceptance of the injection line with different transverse emittance output by RFQ.

    横向发射度
    /(mm·mrad)
    质子束209Bi32+
    传输
    效率/%
    接受
    效率/%
    传输
    效率/%
    接受
    效率/%
    0.5π24.1917.8457.4835.29
    0.4π31.2624.3772.1646.72
    0.3π42.2532.3185.9856.94
    0.2π56.8047.5695.8674.00
    0.1π74.4068.1896.6892.63
    下载: 导出CSV

    表 3  注入线束流发射度、环的接受度及twiss参数对比

    Table 3.  List of the injection beam emittance, ring acceptance and twiss parameters.

    注入束流参数环的接受参数
     εx/(mm·mrad)13.1π200π
     εy/ (mm·mrad)9.7π30π
     βx/m1.634.963
     βy/m1.692.105
     αx0.61431.0263
     αy–0.6558–1.1720
     Δp/p/% ± 0.2 ± 0.3
     D0.151.6582
     D'–0.200.9391
    下载: 导出CSV
  • [1]

    Qian C, Sun L T, Jia Z H 2020 Rev. Sci. Instrum 91 023313Google Scholar

    [2]

    刘明 2017 硕士学位论文 (兰州: 近代物理研究所)

    Liu M 2017 M. S. Dissertation (Lanzhou: Institute of Modern Physics) (in Chinese)

    [3]

    喻九维, 杨雅清, 吕明邦, 陈文军, 郑亚军, 许小伟, 陆海娇, 潘永祥 2021 强激光与粒子束 33 054001

    Yu J W, Yang Y Q, Lü M B, Cheng W J, Zheng Y J, Xu X W, Lu H J, Pan Y X 2021 High Power Laser and Particle Beams 33 054001

    [4]

    李钟汕 2017 博士学位论文 (兰州: 近代物理研究所)

    Li Z S 2017 Ph. D. Dissertation (Lanzhou: Institute of Modern Physics) (in Chinese)

    [5]

    Ren H T, Pozdeyev E, Lund M S 2016 Rev. Sci. Instrum. 87 02B919Google Scholar

    [6]

    Akagi T, Bellan L 2020 Rev. Sci. Instrum. 91 023321Google Scholar

    [7]

    Clemente G, Ratzinger U, Podlech H, Groening L, Brodhage R, Barth W 2011 Phys. Rev. Spec. Top. Ac. 14 110101

    [8]

    Yang Y, Dou W P, Sun L T 2016 Rev. Sci. Instrum. 87 02B910Google Scholar

    [9]

    Thuillier T, Angot J, Barue C 2016 Rev. Sci. Instrum. 87 02A733Google Scholar

    [10]

    Benedetti S, Bellodi G, Kuchler D 2018 Rev. Sci. Instrum. 89 123301Google Scholar

    [11]

    Ullmann C, Berezov R, Fils J 2014 Rev. Sci. Instrum. 85 02A952Google Scholar

    [12]

    颜学庆, 陆元荣, 吴瑜, 张宏林, 高淑丽, 方家训 2002 北京大学学报 (自然科学版) 38 1

    Yan X Q, Lu Y R, Wu Y, Zhang H L, Gao S L, Fang J X 2002 Universitatis Pekinensis 38 1

    [13]

    吴瑜 1999 北京大学学报 (自然科学版) 35 3

    Wu Y 1999 Universitatis Pekinensis 35 3

    [14]

    王科栋 2019 博士学位论文 (兰州: 近代物理研究所)

    Wang K D 2017 Ph. D. Dissertation (Lanzhou: Institute of Modern Physics) (in Chinese)

    [15]

    Winklehner D, Hammond R, Alons J 2016 Rev. Sci. Instrum. 87 02B929Google Scholar

    [16]

    Otani M, Mibe T, Yoshida M 2016 Phys. Rev. Accel. Beams 19 040101Google Scholar

    [17]

    He T, Lu L, He Y, Hang Y L, Ma W, Tan T, Zhang Z L, Yang L, Xing C C, Li C X, Sun L P 2021 Nuclear Inst. Meth. Phys. Research A 1010 165466Google Scholar

    [18]

    Wang K D, Yuan Y J, Yin X J, Yang J C, Li Z S, Du H, Li X N, Kong Q Y, Wang K, Dong Z Q, Liu J, Xia J W 2019 Nuclear Inst. Meth. Phys. Research A 927 375Google Scholar

    [19]

    Uriot D 2003 Proceedings of the 2003 Particle Accelerator Conference, Portland, USA, May 12–16, 2003 p3491

    [20]

    吕建钦 2003 带电粒子束光学 (北京: 高等教育出版社) 第267页

    Lv J Q 2003 The Optics of Charged Particle Beams (Beijing: Higher Education Press) p267 (in Chinese)

    [21]

    陈佳洱 2019 加速器物理基础 (北京: 北京大学出版社) 第353页

    Chen J Er 2019 Foundment Physics of Accelerator (Beijing: Peking University Press) p353 (in Chinese)

  • [1] 周贤韬, 江英华. 带身份认证的量子安全直接通信方案. 物理学报, 2023, 72(2): 020302. doi: 10.7498/aps.72.20221684
    [2] 周贤韬, 江英华, 郭晓军, 彭展. 带双向身份认证的基于单光子和Bell态混合的量子安全直接通信方案. 物理学报, 2023, 72(13): 130302. doi: 10.7498/aps.72.20221972
    [3] 唐传祥, 邓秀杰. 稳态微聚束加速器光源. 物理学报, 2022, 71(15): 152901. doi: 10.7498/aps.71.20220486
    [4] 田永顺, 胡志良, 童剑飞, 陈俊阳, 彭向阳, 梁天骄. 基于3.5 MeV射频四极质子加速器硼中子俘获治疗装置的束流整形体设计. 物理学报, 2018, 67(14): 142801. doi: 10.7498/aps.67.20180380
    [5] 曹正文, 赵光, 张爽浩, 冯晓毅, 彭进业. 基于Bell态粒子和单光子混合的量子安全直接通信方案. 物理学报, 2016, 65(23): 230301. doi: 10.7498/aps.65.230301
    [6] 孙亚秀, 卓庆坤, 姜庆辉, 李千. 基于多导体传输线理论的差模激励新型线束串扰模型研究. 物理学报, 2015, 64(4): 044102. doi: 10.7498/aps.64.044102
    [7] 袁颖. 利用超相对论量子分子动力学模型研究交变梯度同步加速器能区Au+Au碰撞中的核阻止效应. 物理学报, 2013, 62(22): 222402. doi: 10.7498/aps.62.222402
    [8] 陈代兵, 王冬, 秦奋, 文杰, 金晓, 安海狮, 张新凯. 磁绝缘线振荡器的起振电压与注入电压关系的分析. 物理学报, 2012, 61(1): 012901. doi: 10.7498/aps.61.012901
    [9] 耿少飞, 唐德礼, 邱孝明, 聂军伟, 于毅军. 霍尔漂移对阳极层霍尔等离子体加速器电离效率的影响. 物理学报, 2012, 61(7): 075210. doi: 10.7498/aps.61.075210
    [10] 陈子伦, 周 朴, 许晓军, 侯 静, 姜宗福. 谱线和耦合系数对光纤激光器相互注入锁定的影响. 物理学报, 2008, 57(6): 3588-3592. doi: 10.7498/aps.57.3588
    [11] 杨海亮, 邱爱慈, 李静雅, 孙剑锋, 何小平, 汤俊萍, 王海洋, 黄建军, 任书庆, 邹丽丽, 杨 莉. 叠片法测量“闪光二号”加速器的高功率离子束能谱. 物理学报, 2005, 54(9): 4072-4078. doi: 10.7498/aps.54.4072
    [12] 邬鹏举, 李玉德, 林晓燕, 刘安东, 孙天希. x射线在毛细导管中传输的模拟计算. 物理学报, 2005, 54(10): 4478-4482. doi: 10.7498/aps.54.4478
    [13] 朱伦武, 翁甲强, 高远, 方锦清. 强流加速器中束晕-混沌的延迟反馈控制. 物理学报, 2002, 51(7): 1483-1488. doi: 10.7498/aps.51.1483
    [14] 高远, 翁甲强, 方锦清, 罗晓曙. 强流加速器中束晕-混沌的小波间隔反馈控制. 物理学报, 2001, 50(8): 1440-1446. doi: 10.7498/aps.50.1440
    [15] 匡锦瑜, 邓昆, 黄荣怀. 利用时空混沌同步进行数字加密通信. 物理学报, 2001, 50(10): 1856-1861. doi: 10.7498/aps.50.1856
    [16] 吴正云, 黄启圣. 聚焦Ga+离子束注入方法研制半导体量子线结构. 物理学报, 1996, 45(3): 486-490. doi: 10.7498/aps.45.486
    [17] 方守贤, 魏开煜. 螺旋线迴旋加速器中粒子流通过非线性共振线(Qρ=(6/5))的研究. 物理学报, 1964, 20(7): 636-642. doi: 10.7498/aps.20.636
    [18] 方守贤, 魏开煜. 螺旋线迴旋加速器中粒子径向自由振荡的静态分析. 物理学报, 1964, 20(4): 305-310. doi: 10.7498/aps.20.305
    [19] 叶铭汉, 孙良方, 徐建铭, 金建中, 叶龙飞, 陈志诚, 陈鑑璞, 夏广昌, 余觉先, 李正武, 赵忠尧. 质子静电加速器. 物理学报, 1963, 19(1): 60-69. doi: 10.7498/aps.19.60
    [20] 申青鹤, 蒋崧生, 顾以藩. 迥旋加速器离子束的脈冲调制. 物理学报, 1960, 16(2): 94-97. doi: 10.7498/aps.16.94
计量
  • 文章访问数:  3871
  • PDF下载量:  87
  • 被引次数: 0
出版历程
  • 收稿日期:  2021-11-16
  • 修回日期:  2022-02-05
  • 上网日期:  2022-03-04
  • 刊出日期:  2022-06-05

/

返回文章
返回