-
Bismuth brass has very good mechanical properties and is friendly to environment. Therefore, it can be widely used in different fields. In order to realize the convenient, rapid and sensitive elemental analysis of trace elements in bismuth brass, fiber laser based high repetition rate laser-ablation spark-induced breakdown spectroscopy (HRR LA-SIBS) is developed. In the experiments, a compact fiber laser operated at 5 kHz pulse repetition rate is used to ablate the sample and produce plasma, and the spark discharge is used to further break down the ablated sample and enhance the plasma emission for sensitive elemental analysis. A compact fiber-optic spectrometer coupled with non-intensified charge-coupled device (CCD) is used to record the spectra. Bismuth, lead and tin in several bismuth brass standard samples are quantitatively analyzed. The plasma temperature is determined to be about 7962 ± 300 K by using the Boltzmann plots of copper, zinc and tin elements; the electron density is determined to be about 1.049 × 10–17 cm–3 based on the Stark broadening of Cu (I) 510.47 nm analytical line. The plasma is determined to be in local thermodynamic equilibrium (LTE) state according to McWhirter criterion as well as appended criteria for transient plasma. Under the present experimental condition, the calibration curves of bismuth, lead and tin in bismuth brass are built with fitting goodness of higher than 95%. The detection limits of bismuth, lead and tin are determined to be 25.5 ppm, 64.2 ppm and 316.5 ppm, respectively. The weak transition probability of tin atoms leads to worse detection limit of tin than the scenarios of bismuth and lead. The ways to further improve the analytical sensitivity and minimize system dimensions are discussed in this article. It is demonstrated that high repetition rate laser-ablation spark-induced breakdown spectrometer based on compact fiber laser as well as compact fiber-optic spectrometer can be used to realize the convenient, rapid and sensitive elemental analysis of trace elements in bismuth brass. This study is also helpful in analyzing the trace harmful elements, including bismuth, lead and tin in high temperature alloys with HRR LA-SIBS. In comparison with laser-induced breakdown spectroscopy (LIBS), the HRR LA-SIBS technique has several intrinsic advantages, such as fast spectral data collection speed, cost-effective system and low continuum background and so on. This technique is very useful in implementing the elemental analysis of different alloy samples and can be potentially used in metallurgical industry in the future.
-
Keywords:
- laser-ablation /
- spark-induced breakdown spectroscopy /
- bismuth brass /
- elemental analysis /
- compact
[1] 肖来荣, 舒学鹏, 易丹青, 张路怀, 覃静丽, 胡加瑞 2009 中南大学学报 (自然科学版) 40 117
Xiao L R, Shu X P, Yi D Q, Zhang L H, Qin J L, Hu J R 2009 J. Cent. South Univ. (Sci. Technol.) 40 117
[2] Thangavel S, Dash K, Dhavile S M, Sahayam A C 2015 Talanta 131 505
Google Scholar
[3] Zhu D, Wang X, Ni X W, Cheng J P, Lu J 2011 Plasma Sci. Technol. 13 486
Google Scholar
[4] Zhao T Z, Fan Z W, Lian F Q, Liu Y, Lin W R, Mo Z Q, Nie S Z, Wang P, Xiao H, Li X, Zhong Q X, Zhang H G 2017 Spectrochim. Acta, Part B 137 64
Google Scholar
[5] Gojani A B 2012 ISRN Spectrosc. 2012 868561
[6] 崔执凤, 张先, 姚关心, 汪小丽, 许新胜, 郑贤锋, 凤尔银, 季学韩 2006 物理学报 55 4506
Google Scholar
Cui Z F, Zhang X, Yao G X, Wang X L, Xu X S, Zheng X F, Feng E Y, Ji X H 2006 Acta Phys. Sin. 55 4506
Google Scholar
[7] 陈添兵, 姚明印, 刘木华, 林永增, 黎文兵, 郑美兰, 周华茂 2014 物理学报 63 104213
Google Scholar
Chen T B, Yao M Y, Liu M H, Lin Y Z, Li W B, Zheng M L, Zhou H M 2014 Acta Phys. Sin. 63 104213
Google Scholar
[8] 杜闯, 高勋, 邵妍, 宋晓伟, 赵振明, 郝作强, 林景全 2013 物理学报 62 045202
Google Scholar
Du C, Gao X, Shao Y, Song X W, Zhao Z M, Hao Z Q, Lin J Q 2013 Acta Phys. Sin. 62 045202
Google Scholar
[9] Li C M, Hao Z Q, Zou Z M, Zhou R, Li J M, Guo L B, Li X Y, Lu Y F, Zeng X Y 2016 Opt. Express 24 7850
Google Scholar
[10] Laville S, Goueguel C, Loudyi H, Vidal F, Chaker M, Mohamad S 2009 Spectrochim. Acta, Part B 64 347
Google Scholar
[11] Wang Y R, Kang J, Chen Y Q, Li R H 2019 J. Appl. Spectrosc. 86 353
Google Scholar
[12] Kang J, Chen Y Q, Li R H 2019 Spectrochim. Acta, Part B 161 105711
Google Scholar
[13] Jiang Y H, Li R H, Chen Y Q 2019 J. Anal. At. Spectrom. 34 1838
Google Scholar
[14] He X Y, Li R H, Wang F J 2019 Plasma Sci. Technol. 21 034005
Google Scholar
[15] Ciucci A, Corsi M, Palleschi V, Rastelli S, Tognoni E 1999 Appl. Spectrosc. 53 960
Google Scholar
[16] Zmerli B, Ben Nessib N, Dimitrijevi M S, Sahal-Bréchot S 2010 Phys. Scr. 82 055301
Google Scholar
[17] Gao J K, Kang J, Li R H, Chen Y Q 2020 Appl. Opt. 59 4091
Google Scholar
[18] Cristoforetti G, Giacomo A D, Dell’Aglio M, Legnaioli S, Tognoni E, Palleschi V, Omenetto N 2010 Spectrochim. Acta, Part B 65 86
Google Scholar
[19] Regemorter H V 1962 Astrophys. J. 136 906
Google Scholar
[20] Aragon C, Aguilera J A, Penalba F 1999 Appl. Spectrosc. 53 1259
Google Scholar
[21] Chen Z J, Li H K, Zhao F, Li R H 2008 J. Anal. At. Spectrom. 23 871
Google Scholar
-
图 1 基于光纤激光器的HRR LA-SIBS的实验装置示意图
Figure 1. Schematic diagram of the experimental setup of fiber laser based HRR LA-SIBS.
图 2 校准后的2号样品的局部光谱图
Figure 2. The calibrated partial spectrum of sample No. 2.
图 3 用于测定等离子体温度的玻尔兹曼图
Figure 3. Boltzmann plots used to estimate the plasma temperature.
图 4 Cu I 510.47 nm谱线的洛伦兹拟合图
Figure 4. Lorentzian fit of Cu I line.
图 5 校准后的2号样品的局部光谱图
Figure 5. The calibrated partial spectrum of sample No.2.
图 6 用HRR LA-SIBS分析铋黄铜中铋、铅和锡的校正曲线 (a) Bi; (b) Pb; (c) Sn
Figure 6. Calibration curves of bismuth, lead and tin in bismuth brass analyzed with HRR LA-SIBS: (a) Bi; (b) Pb; (c) Sn.
表 1 标准样品中铋、铅和锡元素的质量分数
Table 1. List of the mass fraction (%) of bismuth, lead and tin in standard samples.
Sample No. Bi Pb Sn 1 3.002 0.0054 1.038 2 0.414 0.105 0.306 3 1.561 0.0161 0.518 4 0.826 0.0209 2.007 5 0.108 0.0059 3.020 6 0.0058 — — 
DownLoad: CSV
表 2 计算等离子体温度所选择的谱线及相应能级与跃迁参数列表
Table 2. List of the energy level and transition probability of the selected lines for plasma temperature calculation.
Species $\lambda $/nm A/s–1 gk Ek/eV Cu Ⅰ 261.83 3.07 × 107 4 6.120 Cu Ⅰ 282.43 0.78 × 107 6 5.780 Cu Ⅰ 306.34 1.55 × 106 4 5.688 Cu Ⅰ 319.40 1.55 × 106 4 5.523 Cu Ⅰ 333.78 0.38 × 106 8 5.102 Cu Ⅰ 406.26 2.10 × 107 6 6.868 Cu Ⅰ 510.55 0.20 × 107 4 3.820 Cu Ⅰ 515.32 0.60 × 108 4 6.190 Zn Ⅰ 307.58 0.38 × 106 3 4.030 Zn Ⅰ 328.23 9.00 × 107 3 7.780 Zn Ⅰ 330.25 1.20 × 108 5 7.783 Zn Ⅰ 334.50 1.70 × 108 7 7.783 Sn Ⅰ 242.94 1.50 × 108 7 5.527 Sn Ⅰ 270.65 6.60 × 107 5 4.789 Sn Ⅰ 283.99 1.70 × 108 5 4.789 Sn Ⅰ 286.33 5.40 × 107 3 4.329 Sn Ⅰ 300.91 3.80 × 107 3 4.329 Sn Ⅰ 303.41 2.00 × 108 1 4.295 Sn Ⅰ 317.50 1.00 × 108 3 4.329 Sn Ⅰ 326.23 2.70 × 108 3 4.867
DownLoad: CSV
表 3 铋黄铜中铋、铅、锡三元素的HRR LA-SIBS分析结果
Table 3. Analytical results of bismuth, lead and tin in bismuth brass with HRR LA-SIBS.
Analytical line S σB R2 LOD/10–6 Bi Ⅰ 306.77 nm 1.818 0.00155 0.98 25.5 Pb Ⅰ 405.78 nm 1.376 0.0029 0.98 64.2 Sn Ⅰ 326.23 nm 0.210 0.0022 0.96 316.5
DownLoad: CSV
-
[1] 肖来荣, 舒学鹏, 易丹青, 张路怀, 覃静丽, 胡加瑞 2009 中南大学学报 (自然科学版) 40 117
Xiao L R, Shu X P, Yi D Q, Zhang L H, Qin J L, Hu J R 2009 J. Cent. South Univ. (Sci. Technol.) 40 117
[2] Thangavel S, Dash K, Dhavile S M, Sahayam A C 2015 Talanta 131 505
Google Scholar
[3] Zhu D, Wang X, Ni X W, Cheng J P, Lu J 2011 Plasma Sci. Technol. 13 486
Google Scholar
[4] Zhao T Z, Fan Z W, Lian F Q, Liu Y, Lin W R, Mo Z Q, Nie S Z, Wang P, Xiao H, Li X, Zhong Q X, Zhang H G 2017 Spectrochim. Acta, Part B 137 64
Google Scholar
[5] Gojani A B 2012 ISRN Spectrosc. 2012 868561
[6] 崔执凤, 张先, 姚关心, 汪小丽, 许新胜, 郑贤锋, 凤尔银, 季学韩 2006 物理学报 55 4506
Google Scholar
Cui Z F, Zhang X, Yao G X, Wang X L, Xu X S, Zheng X F, Feng E Y, Ji X H 2006 Acta Phys. Sin. 55 4506
Google Scholar
[7] 陈添兵, 姚明印, 刘木华, 林永增, 黎文兵, 郑美兰, 周华茂 2014 物理学报 63 104213
Google Scholar
Chen T B, Yao M Y, Liu M H, Lin Y Z, Li W B, Zheng M L, Zhou H M 2014 Acta Phys. Sin. 63 104213
Google Scholar
[8] 杜闯, 高勋, 邵妍, 宋晓伟, 赵振明, 郝作强, 林景全 2013 物理学报 62 045202
Google Scholar
Du C, Gao X, Shao Y, Song X W, Zhao Z M, Hao Z Q, Lin J Q 2013 Acta Phys. Sin. 62 045202
Google Scholar
[9] Li C M, Hao Z Q, Zou Z M, Zhou R, Li J M, Guo L B, Li X Y, Lu Y F, Zeng X Y 2016 Opt. Express 24 7850
Google Scholar
[10] Laville S, Goueguel C, Loudyi H, Vidal F, Chaker M, Mohamad S 2009 Spectrochim. Acta, Part B 64 347
Google Scholar
[11] Wang Y R, Kang J, Chen Y Q, Li R H 2019 J. Appl. Spectrosc. 86 353
Google Scholar
[12] Kang J, Chen Y Q, Li R H 2019 Spectrochim. Acta, Part B 161 105711
Google Scholar
[13] Jiang Y H, Li R H, Chen Y Q 2019 J. Anal. At. Spectrom. 34 1838
Google Scholar
[14] He X Y, Li R H, Wang F J 2019 Plasma Sci. Technol. 21 034005
Google Scholar
[15] Ciucci A, Corsi M, Palleschi V, Rastelli S, Tognoni E 1999 Appl. Spectrosc. 53 960
Google Scholar
[16] Zmerli B, Ben Nessib N, Dimitrijevi M S, Sahal-Bréchot S 2010 Phys. Scr. 82 055301
Google Scholar
[17] Gao J K, Kang J, Li R H, Chen Y Q 2020 Appl. Opt. 59 4091
Google Scholar
[18] Cristoforetti G, Giacomo A D, Dell’Aglio M, Legnaioli S, Tognoni E, Palleschi V, Omenetto N 2010 Spectrochim. Acta, Part B 65 86
Google Scholar
[19] Regemorter H V 1962 Astrophys. J. 136 906
Google Scholar
[20] Aragon C, Aguilera J A, Penalba F 1999 Appl. Spectrosc. 53 1259
Google Scholar
[21] Chen Z J, Li H K, Zhao F, Li R H 2008 J. Anal. At. Spectrom. 23 871
Google Scholar
DownLoad:
Catalog
Metrics
- Abstract views: 4665
- PDF Downloads: 52
- Cited By: 0
