-
In this paper, molecular dynamics method is used to simulate the evolution mechanism of void nucleation, growth and closure of diffusion-welded copper/aluminum bilayer film under cyclic loading condition with a strain-to-width ratio of R = –1. It is found that under cyclic loading condition, the voids mainly nucleate inside the aluminum side of the copper/aluminum bilayer film, and two kinds of evolution modes of voids I and II are found. The void I nucleates at the position of the gap defect produced by the Kirkendall effect when the copper-aluminum diffuses to form the bilayer film. Under this nucleation mode, after the gap defects have become void, the void moves into the area where copper atoms are relatively dense inside the OTHER structure on the aluminum side. When gaps accumulate to form voids, the voids grow at a fixed position. The void II on the aluminum side nucleates at the position of the gap defect formed by overcoming the stair-rod dislocation and then remains motionless in the process of nucleation, growth and closure. Comparing with the void I, the stress corresponding to the nucleation of void II is large, the growth speed of the void II is fast and the size of the void II is slightly large in the process of strain loading. The void II closure speed is also faster in the strain unloading stage. The two kinds of voids have two common characteristics in the process of nucleation, growth and closure. 1) Both kinds of voids nucleate at the position of the gap defect inside OTHER structure on the aluminum side. 2) In the process of voids growth and closure, both kinds of voids have the same shape changes. In the void growth stage, both kinds of voids first grow along the strain loading direction, then expand in the direction perpendicular to the strain loading direction, and finally, the shapes of two kinds of voids tend to become spherical. In the stage of void closure, the two kinds of voids are first compressed into ellipsoidal shape along the strain loading direction, and then disappear from both ends of the void to the center of the void in the direction perpendicular to the strain loading direction. In the subsequent cyclic loading process, none of new voids appears again at the position where the voids disappearred, but the nucleation of voids at other position of gap defect forms inside the other structure located on the aluminum side.
-
Keywords:
- molecular dynamics /
- Cu/Al film /
- cyclic load /
- void
[1] 莫里斯著 (罗小兵, 陈明祥译) 2013 纳米封装: 纳米技术与电子封装 (北京: 机械工业出版社) 第394−419页
Morris J E (translated by Luo X B, Chen X Y) 2013 Nanopackaging Nanotechnologies and Electronics Packaging (Beijing: Machinery Industry Press) pp394−419 (in Chinese)
[2] 谢军, 吴卫东, 叶成钢, 黄丽珍, 袁光辉 2004 强激光与粒子束 16 607
Xie J, Wu W D, Ye C G, Huang L Z, Yuan G H 2004 High Pow. Las. Part. Beam 16 607
[3] 谢军, 吴卫东, 杜凯, 郑凤成, 叶成钢, 黄丽珍, 袁光辉 2004 原子能科学技术 38 120
Google Scholar
Xie J, Wu W D, Du K, Zheng F C, Ye C G, Huang L Z, Yuan G H 2004 Atom. Energ Sci. Technol. 38 120
Google Scholar
[4] Zhou Q, Li S, Huang P, Xu K W, Wang F, Lu T J 2016 APL Mater. 4 096102
Google Scholar
[5] 刘浩, 柯孚久, 潘晖, 周敏 2007 物理学报 56 407
Google Scholar
Liu H, Ke F J, Pan H, Zhou M 2007 Acta Phys. Sin. 56 407
Google Scholar
[6] 王长健 2017 金属热处理 42 204
Wang C J 2017 Heat Treat Met. 42 204
[7] 赵艳红, 李英骏, 杨志安, 张广财 2006 计算物理 23 343
Google Scholar
Zhao Y H, Li Y J, Yang Z A, Zhang G C 2006 Chin. J. Comput. Phys. 23 343
Google Scholar
[8] 徐爽, 郭雅芳 2013 物理学报 62 196201
Google Scholar
Xu S, Guo Y F 2013 Acta Phys. Sin. 62 196201
Google Scholar
[9] Zheng H, Liu H F, Zhang G C 2004 Comp. Mater. Sci. 30 230
Google Scholar
[10] 庞卫卫, 张广财, 许爱国, 卢果 2011 计算物理 28 540
Google Scholar
Pang W W, Zhang G C, Xu A G, Lu G 2011 Chin. J. Comput. Phys. 28 540
Google Scholar
[11] 李亚江, 吴会强, 陈茂爱, 杨敏, 冯涛 2001 中国有色金属学报 11 424
Google Scholar
Li Y J, Wu H Q, Chen M A, Yang M, Feng T 2001 Chin. J. Nonferrous Met. 11 424
Google Scholar
[12] 白莉 2012 热加工工艺 41 167
Google Scholar
Bai L 2012 Hot Work. Technol. 41 167
Google Scholar
[13] Li X B, Zu G Y, Wang P 2015 Trans. Nonferrous Met. Soc. China 25 36
Google Scholar
[14] 路王珂, 谢敬佩, 王爱琴, 李继文, 张银娣 2014 机械工程材料 38 14
Lu W K, Xie J P, Wang A Q, Li J W, Zhang Y D 2014 Mater. Mech. Eng. 38 14
[15] 王波, 张洪涛, 朱训明, 王云峰, 金伟, 何鹏 2018 机械工程学报 54 95
Wang B, Zhang H T, Zhu X M, Wang Y F, Jin W, He P 2018 Chin. J. Mech. Eng. 54 95
[16] 成聪, 陈尚达, 吴勇芝, 黄鸿翔 2015 材料工程 43 60
Google Scholar
Cheng C, Chen S D, Wu Y Z, Huang H X 2015 J. Mater. Eng. 43 60
Google Scholar
[17] Wang Y C, Liang F, Tan H F, Zhang B, Zhang G P 2018 Mater. Sci. Eng. A 714 43
Google Scholar
[18] 祁美兰 2006 博士学位论文 (武汉: 武汉理工大学)
Qi M L 2006 Ph. D. Dissertation (Wuhan: Wuhan University of Technology) (in Chinese)
[19] 冉小霞 2015 硕士学位论文 (武汉: 武汉理工大学)
Ren X X 2015 M. S. Thesis (Wuhan: Wuhan University of Technology) (in Chinese)
[20] 徐斌, 孙明月, 李殿中 2012 金属学报 48 1194
Xu B, Sun M Y, Li D Z 2012 Acta Metall. Sin. 48 1194
[21] 刘宏伟 2010 硕士学位论文 (宁波: 宁波大学)
Liu H W 2010 M. S. Thesis (Ningbo: Ningbo University) (in Chinese)
[22] Avinash M D, Arunachalam M R, Bruce L, Mohammed A Z, Donald W B 2009 Phys. Rev. B 80 104108
Google Scholar
[23] 庞卫卫, 张平, 张广财, 许爱国, 赵宪庚 2012 中国科学 42 464
Pang W W, Zhang P, Zhang G C, Xu A G, Zhao X G 2012 Sci. China 42 464
[24] Belak J 1998 J. Comput. Aided Mater. Des. 5 193
Google Scholar
[25] Sirirat T, Eduardo M B, David J B, Marc A M 2008 Acta Mater. 56 3874
Google Scholar
[26] 张宁, 杨新华, 陈传尧 2010 计算力学学报 27 330
Google Scholar
Zhang N, Yang X H, Chen C Y 2010 Chin. J. Comput. Mech. 27 330
Google Scholar
[27] Simar A, Voigt H L, Wirth B D 2011 Comp. Mater. Sci. 50 1811
Google Scholar
[28] 胡晓燕, 徐建刚, 闫新兴 2012 兵器材料科学与工程 35 52
Google Scholar
Hu X Y, Xu J G, Yan X X 2012 Ordn. Mater. Sci. Eng. 35 52
Google Scholar
[29] 梁华, 李茂生 2019 计算物理 36 211
Liang H, Li M S 2019 Chin. J. Comput. Phys. 36 211
[30] 方洲, 刘晓波, 徐庆军 2018 机械设计与制造 32
Google Scholar
Fang Z, Liu X B, Xu Q J 2018 Machinery Design & Manufacture 32
Google Scholar
[31] Yang X H, Zhou T, Chen C Y 2007 Comp. Mater. Sci. 40 51
Google Scholar
[32] 郭巧能, 曹义刚, 孙强, 刘忠侠, 贾瑜, 霍裕平 2013 物理学报 62 107103
Google Scholar
Guo Q N, Cao Y G, Sun Q, Liu Z X, Jia Y, Huo Y P 2013 Acta Phys. Sin. 62 107103
Google Scholar
[33] 张永军 2003 博士学位论文 (北京: 北京科技大学)
Zhang Y J 2003 Ph. D. Dissertation (Beijing: University of Science & Technology Beijing)
[34] Cai J, Ye Y Y 1996 Phys. Rev. B 54 8398
Google Scholar
[35] Plimpton S 1995 J. Comput. Phys. 117 1
Google Scholar
[36] 韩雪杰 2018 硕士学位论文 (郑州: 郑州大学)
Han X J 2018 M. S. Thesis (Zhenzhou: Zhengzhou University) (in Chinese)
[37] Evans D J, Holian B L 1985 J. Chen. Phys. 83 4069
Google Scholar
[38] Stukowski A 2010 Modelling Simul. Mater. Sci. Eng. 18 015012
Google Scholar
[39] 张宝昌 1993 有色金属及其热处理 (西安: 西北工业大学出版社) 第128−145页
Zhang B C 1993 Nonferrous metals and their heat treatment (Xi'an: Northwest Polytechnic University Press) pp128−145
[40] 马欢欢 2008 硕士学位论文 (沈阳: 沈阳工业大学)
Ma H H 2008 M. S. Thesis (Shenyang: Shenyang University of Technology)
[41] 徐振海, 袁林, 单德彬, 郭斌 2009 物理学报 58 4835
Google Scholar
Xu Z H, Yuan L, Shan D B, Guo B 2009 Acta Phys. Sin. 58 4835
Google Scholar
[42] 杨振 2017 博士学位论文 (北京: 北京有色金属研究总院)
Yang Z 2017 Ph. D. Dissertation (Beijing: General Research Institute for Nonferrous Metals) (in Chinese)
[43] 杜文佳, 谢明, 溥存继, 陈永泰, 杨云峰, 张吉明, 刘满门, 胡洁琼, 王塞北 2013 材料热处理学报 33 14
Du W J, Xie M, Pu C J, Chen Y T, Yang Y F, Zhang J M, Liu M M, Hu J Q, Wang S B 2013 T. Mater. Heat Treat. 33 14
[44] 王吉会, 郑俊萍, 刘家臣, 黄定海 2006 材料力学性能 1 (天津: 天津大学出版社) 第13−40页
Wang J H, Zheng J P, Liu J C, Huang D H 2006 Mechanical Behavior of Materials 1 (Tianjin:Tianjin University Press) pp13−40 (in Chinese)
[45] 李永华, 檀雯, 张宁, 王勇, 邓子玉 2008 沈阳理工大学学报 27 64
Google Scholar
Li Y H, Tan W, Zhang N, Wang Y, Deng Z Y 2008 J. Shenyang Ligong Univ. 27 64
Google Scholar
[46] Guo Q N, Yue X D, Yang S E, Huo Y P 2010 Comp. Mater. Sci. 50 319
Google Scholar
[47] Ohkubo H, Shimomura Y, Mukouda I, Sugio K, Kiritani M 2003 Mater. Sci. Eng. A 350 30
Google Scholar
[48] 杨彪, 郑百林, 胡兴健, 贺鹏飞, 岳珠峰 2016 金属学报 52 129
Google Scholar
Yang B, Zheng B L, Hu X J, He P F, Yue Z F 2016 Acta Metall. Sin. 52 129
Google Scholar
-
图 1 纳米铜/铝双层膜模型(注: 上层蓝色为铜原子, 下层红色为铝原子)
Figure 1. Cu/Al bilayer films model (The upper blue for copper atoms and the lower red for aluminum atoms).
图 2 纳米铜/铝双层膜在循环载荷作用下应力-时间曲线
Figure 2. Stress-time curve of Cu/Al bilayer films under cyclic loading.
图 3 孔洞Ⅰ: 孔洞形核演化截图(红色代表铝原子, 蓝色代表铜原子) ε分别为(a) 0.0000; (b) 0.0528; (c) 0.0531; (d) 0.0534; (e) 0.0537; (f) 0.0540
Figure 3. Void I: screenshot of the nucleation evolution of the void (red for aluminum atoms, blue for copper atoms), ε is (a) 0.0000; (b) 0.0528; (c) 0.0531; (d) 0.0534; (e) 0.0537; (f) 0.0540.
图 4 孔洞Ⅰ: 孔洞形核演化的原子结构分析截图(红色代表HCP结构, 绿色代表FCC结构, 白色代表OTHER结构) ε分别为(a) 0.0000; (b) 0.0528; (c) 0.0531; (d) 0.0534; (e) 0.0537; (f) 0.0540
Figure 4. Void I: screenshot of the atomic structure of nucleation evolution of the void (red for HCP structure, green for FCC structure, white for OTHER structure), ε is (a) 0.0000; (b) 0.0528; (c) 0.0531; (d) 0.0534; (e) 0.0537; (f) 0.0540.
图 5 ε = 0.0510时, 孔洞Ⅰ: 孔洞形核位置处的位错分析截图(红色原子为HCP结构原子, 紫色为
$\langle 110\rangle/6$ 压杆位错线, 绿色为$\langle 112\rangle/6$ 肖克莱位错线, 深红色为OTHER结构位错线)Figure 5. ε = 0.0510, Void I: screenshot of dislocation analysis at the nucleation position of the void (red atoms are HCP structure atoms, purple represents
$\langle 110\rangle/6$ the stair-rod dislocation line, green represents$\langle 112\rangle/6$ the shockley dislocation line, dark red represents the OTHER structure dislocation line).
图 6 ε = 0.0528时, 孔洞Ⅰ: 孔洞形核位置处的位错分析截图(红色原子为HCP结构原子, 紫色为
$\langle 110\rangle/6$ 压杆位错线, 绿色为$\langle 112\rangle/6$ 肖克莱位错线, 深红色为OTHER结构位错线)Figure 6. ε = 0.0528, Void I: screenshot of dislocation analysis at the nucleation position of the void (red atoms for HCP structure atoms, purple represents
$\langle 110\rangle/6$ the stair-rod dislocation line, green represents$\langle 112\rangle/6$ the shockley dislocation line, dark red represents the OTHER structure dislocation line).
图 7 ε = 0.0537时, 孔洞Ⅰ: 孔洞形核位置处的位错分析截图(红色原子为HCP结构原子, 紫色为
$\langle 110\rangle/6$ 压杆位错线, 绿色为$\langle 112\rangle/6$ 肖克莱位错线, 深红色为OTHER结构位错线)Figure 7. ε = 0.0537, Void I: screenshot of dislocation analysis at the nucleation position of the void (red atoms are HCP structure atoms, purple represents
$\langle 110\rangle/6$ the stair-rod dislocation line, green represents$\langle 112\rangle/6$ the shockley dislocation line, dark red represents the OTHER structure dislocation line).
图 8 孔洞Ⅰ: 孔洞生长演化图(红色代表铝原子, 蓝色代表铜原子) ε分别为(a) 0.0540; (b) 0.0600; (c) 0.0750; (d) 0.0900; (e) 0.1050; (f) 0.1206
Figure 8. Void I: screenshot of the growth evolution of the void (red for aluminum atoms, blue for copper atoms), ε is (a) 0.0540; (b) 0.0600; (c) 0.0750; (d) 0.0900; (e) 0.1050; (f) 0.1206.
图 9 孔洞Ⅰ: 孔洞生长演化的原子结构分析截图(红色代表HCP结构, 绿色代表FCC结构, 白色代表OTHER结构) ε分别为(a) 0.0540; (b) 0.0600; (c) 0.0750; (d) 0.0900; (e) 0.1050; (f) 0.1206
Figure 9. Void I: screenshot of the atomic structure of the growth evolution of the void (red for the HCP structure, green for the FCC structure, white for the OTHER structure), ε is (a) 0.0540; (b) 0.0600; (c) 0.0750; (d) 0.0900; (e) 0.1050; (f) 0.1206.
图 10 扩散后铜和铝原子在拉伸方向(Z轴)的原子浓度分布
Figure 10. Atomic concentration distribution of copper and aluminum atoms in the tensile direction (Z-axis) after diffusion.
图 11 孔洞Ⅰ: 孔洞闭合演化图(红色代表铝原子, 蓝色代表铜原子) ε分别为(a) 0.0906; (b) 0.0606; (c) 0.0306; (d) 0.0006; (e) –0.0294; (f) –0.0444
Figure 11. Void I: screenshot of the closure evolution of the void (red for aluminum atoms, blue for copper atoms), ε is (a) 0.0906; (b) 0.0606; (c) 0.0306; (d) 0.0006; (e) –0.0294; (f) –0.0444.
图 12 孔洞Ⅰ: 孔洞闭合演化的原子结构分析截图(红色代表HCP结构, 绿色代表FCC结构, 白色代表OTHER结构) ε分别为(a) 0.0906; (b) 0.0606; (c) 0.0306; (d) 0.0006; (e) –0.0294; (f) –0.0444
Figure 12. Void I: screenshot of the atomic structure of the closure evolution of the void (red for HCP structure, green for FCC structure, white for OTHER structure), ε is (a) 0.0906; (b) 0.0606; (c) 0.0306; (d) 0.0006; (e) –0.0294; (f) –0.0444.
图 13 孔洞Ⅱ: 孔洞形核位置处
$\left( {\bar 111} \right)$ 面位错与$\left( {1\bar 11} \right)$ 面位错交截形成压杆位错的分析图(只显示HCP原子)Figure 13. Void II: An analytical diagram of the stair-rod dislocation formed by the intersection of
$\left( {\bar 111} \right)$ plane dislocations and$\left( {1\bar 11} \right)$ plane dislocations at the nucleation position of the void (only HCP atoms are shown).
图 14 孔洞Ⅱ: 孔洞形核演化图(红色代表铝原子, 蓝色代表铜原子) ε分别为(a) 0.1050; (b) 0.1155; (c) 0.1158; (d) 0.1161; (e) 0.1164; (f) 0.1167
Figure 14. Void Ⅱ: screenshot of the nucleation evolution of the void (red for aluminum atoms, blue for copper atoms), ε is (a) 0.1050; (b) 0.1155; (c) 0.1158; (d) 0.1161; (e) 0.1164; (f) 0.1167.
图 15 孔洞Ⅱ: 孔洞形核演化的原子结构分析截图(红色代表HCP结构, 绿色代表FCC结构, 白色代表OTHER结构) ε分别为(a) 0.1050; (b) 0.1155; (c) 0.1158; (d) 0.1161; (e) 0.1164; (f) 0.1167
Figure 15. Void Ⅱ: screenshot of the atomic structure of the nucleation evolution of the void (red for HCP structure, green for FCC structure, white for OTHER structure), ε is (a) 0.1050; (b) 0.1155; (c) 0.1158; (d) 0.1161; (e) 0.1164; (f) 0.1167.
图 16 孔洞Ⅱ: 孔洞生长演化截图(红色代表铝原子, 蓝色代表铜原子) ε分别为(a) 0.1170; (b) 0.1173; (c) 0.1179; (d) 0.1182; (e) 0.1185; (f) 0.1206
Figure 16. Void Ⅱ: screenshot of the growth evolution of the void (red for aluminum atoms, blue for copper atoms), ε is (a) 0.1170; (b) 0.1173; (c) 0.1179; (d) 0.1182; (e) 0.1185; (f) 0.1206.
图 17 孔洞Ⅱ: 孔洞生长演化的原子结构分析截图(红色代表HCP结构, 绿色代表FCC结构, 白色代表OTHER结构) ε分别为(a) 0.1170; (b) 0.1173; (c) 0.1179; (d) 0.1182; (e) 0.1185; (f) 0.1206
Figure 17. Void Ⅱ: screenshot of the atomic structure of the growth evolution of the void (red for the HCP structure, green for the FCC structure, white for the OTHER structure), ε is (a) 0.1170; (b) 0.1173; (c) 0.1179; (d) 0.1182; (e) 0.1185; (f) 0.1206.
图 18 孔洞Ⅱ: 孔洞闭合演化截图(红色代表铝原子, 蓝色代表铜原子) ε分别为(a) 0.1203; (b) 0.0906; (c) 0.0756; (d) 0.0606; (e) 0.0456; (f) 0.0306
Figure 18. Void Ⅱ: screenshot of the closure evolution of the void (red for aluminum atoms, blue for copper atoms), ε is (a) 0.1203; (b) 0.0906; (c) 0.0756; (d) 0.0606; (e) 0.0456; (f) 0.0306.
图 19 孔洞Ⅱ: 孔洞闭合演化的原子结构分析截图(红色代表HCP结构, 绿色代表FCC结构, 白色代表OTHER结构) ε分别为(a) 0.1203; (b) 0.0906; (c) 0.0756; (d) 0.0606; (e) 0.0456; (f) 0.0306
Figure 19. Void Ⅱ: screenshot of the atomic structure of the closure evolution of the void (red for HCP structure, green for FCC structure, white for OTHER structure), ε is (a) 0.1203; (b) 0.0906; (c) 0.0756; (d) 0.0606; (e) 0.0456; (f) 0.0306.
-
[1] 莫里斯著 (罗小兵, 陈明祥译) 2013 纳米封装: 纳米技术与电子封装 (北京: 机械工业出版社) 第394−419页
Morris J E (translated by Luo X B, Chen X Y) 2013 Nanopackaging Nanotechnologies and Electronics Packaging (Beijing: Machinery Industry Press) pp394−419 (in Chinese)
[2] 谢军, 吴卫东, 叶成钢, 黄丽珍, 袁光辉 2004 强激光与粒子束 16 607
Xie J, Wu W D, Ye C G, Huang L Z, Yuan G H 2004 High Pow. Las. Part. Beam 16 607
[3] 谢军, 吴卫东, 杜凯, 郑凤成, 叶成钢, 黄丽珍, 袁光辉 2004 原子能科学技术 38 120
Google Scholar
Xie J, Wu W D, Du K, Zheng F C, Ye C G, Huang L Z, Yuan G H 2004 Atom. Energ Sci. Technol. 38 120
Google Scholar
[4] Zhou Q, Li S, Huang P, Xu K W, Wang F, Lu T J 2016 APL Mater. 4 096102
Google Scholar
[5] 刘浩, 柯孚久, 潘晖, 周敏 2007 物理学报 56 407
Google Scholar
Liu H, Ke F J, Pan H, Zhou M 2007 Acta Phys. Sin. 56 407
Google Scholar
[6] 王长健 2017 金属热处理 42 204
Wang C J 2017 Heat Treat Met. 42 204
[7] 赵艳红, 李英骏, 杨志安, 张广财 2006 计算物理 23 343
Google Scholar
Zhao Y H, Li Y J, Yang Z A, Zhang G C 2006 Chin. J. Comput. Phys. 23 343
Google Scholar
[8] 徐爽, 郭雅芳 2013 物理学报 62 196201
Google Scholar
Xu S, Guo Y F 2013 Acta Phys. Sin. 62 196201
Google Scholar
[9] Zheng H, Liu H F, Zhang G C 2004 Comp. Mater. Sci. 30 230
Google Scholar
[10] 庞卫卫, 张广财, 许爱国, 卢果 2011 计算物理 28 540
Google Scholar
Pang W W, Zhang G C, Xu A G, Lu G 2011 Chin. J. Comput. Phys. 28 540
Google Scholar
[11] 李亚江, 吴会强, 陈茂爱, 杨敏, 冯涛 2001 中国有色金属学报 11 424
Google Scholar
Li Y J, Wu H Q, Chen M A, Yang M, Feng T 2001 Chin. J. Nonferrous Met. 11 424
Google Scholar
[12] 白莉 2012 热加工工艺 41 167
Google Scholar
Bai L 2012 Hot Work. Technol. 41 167
Google Scholar
[13] Li X B, Zu G Y, Wang P 2015 Trans. Nonferrous Met. Soc. China 25 36
Google Scholar
[14] 路王珂, 谢敬佩, 王爱琴, 李继文, 张银娣 2014 机械工程材料 38 14
Lu W K, Xie J P, Wang A Q, Li J W, Zhang Y D 2014 Mater. Mech. Eng. 38 14
[15] 王波, 张洪涛, 朱训明, 王云峰, 金伟, 何鹏 2018 机械工程学报 54 95
Wang B, Zhang H T, Zhu X M, Wang Y F, Jin W, He P 2018 Chin. J. Mech. Eng. 54 95
[16] 成聪, 陈尚达, 吴勇芝, 黄鸿翔 2015 材料工程 43 60
Google Scholar
Cheng C, Chen S D, Wu Y Z, Huang H X 2015 J. Mater. Eng. 43 60
Google Scholar
[17] Wang Y C, Liang F, Tan H F, Zhang B, Zhang G P 2018 Mater. Sci. Eng. A 714 43
Google Scholar
[18] 祁美兰 2006 博士学位论文 (武汉: 武汉理工大学)
Qi M L 2006 Ph. D. Dissertation (Wuhan: Wuhan University of Technology) (in Chinese)
[19] 冉小霞 2015 硕士学位论文 (武汉: 武汉理工大学)
Ren X X 2015 M. S. Thesis (Wuhan: Wuhan University of Technology) (in Chinese)
[20] 徐斌, 孙明月, 李殿中 2012 金属学报 48 1194
Xu B, Sun M Y, Li D Z 2012 Acta Metall. Sin. 48 1194
[21] 刘宏伟 2010 硕士学位论文 (宁波: 宁波大学)
Liu H W 2010 M. S. Thesis (Ningbo: Ningbo University) (in Chinese)
[22] Avinash M D, Arunachalam M R, Bruce L, Mohammed A Z, Donald W B 2009 Phys. Rev. B 80 104108
Google Scholar
[23] 庞卫卫, 张平, 张广财, 许爱国, 赵宪庚 2012 中国科学 42 464
Pang W W, Zhang P, Zhang G C, Xu A G, Zhao X G 2012 Sci. China 42 464
[24] Belak J 1998 J. Comput. Aided Mater. Des. 5 193
Google Scholar
[25] Sirirat T, Eduardo M B, David J B, Marc A M 2008 Acta Mater. 56 3874
Google Scholar
[26] 张宁, 杨新华, 陈传尧 2010 计算力学学报 27 330
Google Scholar
Zhang N, Yang X H, Chen C Y 2010 Chin. J. Comput. Mech. 27 330
Google Scholar
[27] Simar A, Voigt H L, Wirth B D 2011 Comp. Mater. Sci. 50 1811
Google Scholar
[28] 胡晓燕, 徐建刚, 闫新兴 2012 兵器材料科学与工程 35 52
Google Scholar
Hu X Y, Xu J G, Yan X X 2012 Ordn. Mater. Sci. Eng. 35 52
Google Scholar
[29] 梁华, 李茂生 2019 计算物理 36 211
Liang H, Li M S 2019 Chin. J. Comput. Phys. 36 211
[30] 方洲, 刘晓波, 徐庆军 2018 机械设计与制造 32
Google Scholar
Fang Z, Liu X B, Xu Q J 2018 Machinery Design & Manufacture 32
Google Scholar
[31] Yang X H, Zhou T, Chen C Y 2007 Comp. Mater. Sci. 40 51
Google Scholar
[32] 郭巧能, 曹义刚, 孙强, 刘忠侠, 贾瑜, 霍裕平 2013 物理学报 62 107103
Google Scholar
Guo Q N, Cao Y G, Sun Q, Liu Z X, Jia Y, Huo Y P 2013 Acta Phys. Sin. 62 107103
Google Scholar
[33] 张永军 2003 博士学位论文 (北京: 北京科技大学)
Zhang Y J 2003 Ph. D. Dissertation (Beijing: University of Science & Technology Beijing)
[34] Cai J, Ye Y Y 1996 Phys. Rev. B 54 8398
Google Scholar
[35] Plimpton S 1995 J. Comput. Phys. 117 1
Google Scholar
[36] 韩雪杰 2018 硕士学位论文 (郑州: 郑州大学)
Han X J 2018 M. S. Thesis (Zhenzhou: Zhengzhou University) (in Chinese)
[37] Evans D J, Holian B L 1985 J. Chen. Phys. 83 4069
Google Scholar
[38] Stukowski A 2010 Modelling Simul. Mater. Sci. Eng. 18 015012
Google Scholar
[39] 张宝昌 1993 有色金属及其热处理 (西安: 西北工业大学出版社) 第128−145页
Zhang B C 1993 Nonferrous metals and their heat treatment (Xi'an: Northwest Polytechnic University Press) pp128−145
[40] 马欢欢 2008 硕士学位论文 (沈阳: 沈阳工业大学)
Ma H H 2008 M. S. Thesis (Shenyang: Shenyang University of Technology)
[41] 徐振海, 袁林, 单德彬, 郭斌 2009 物理学报 58 4835
Google Scholar
Xu Z H, Yuan L, Shan D B, Guo B 2009 Acta Phys. Sin. 58 4835
Google Scholar
[42] 杨振 2017 博士学位论文 (北京: 北京有色金属研究总院)
Yang Z 2017 Ph. D. Dissertation (Beijing: General Research Institute for Nonferrous Metals) (in Chinese)
[43] 杜文佳, 谢明, 溥存继, 陈永泰, 杨云峰, 张吉明, 刘满门, 胡洁琼, 王塞北 2013 材料热处理学报 33 14
Du W J, Xie M, Pu C J, Chen Y T, Yang Y F, Zhang J M, Liu M M, Hu J Q, Wang S B 2013 T. Mater. Heat Treat. 33 14
[44] 王吉会, 郑俊萍, 刘家臣, 黄定海 2006 材料力学性能 1 (天津: 天津大学出版社) 第13−40页
Wang J H, Zheng J P, Liu J C, Huang D H 2006 Mechanical Behavior of Materials 1 (Tianjin:Tianjin University Press) pp13−40 (in Chinese)
[45] 李永华, 檀雯, 张宁, 王勇, 邓子玉 2008 沈阳理工大学学报 27 64
Google Scholar
Li Y H, Tan W, Zhang N, Wang Y, Deng Z Y 2008 J. Shenyang Ligong Univ. 27 64
Google Scholar
[46] Guo Q N, Yue X D, Yang S E, Huo Y P 2010 Comp. Mater. Sci. 50 319
Google Scholar
[47] Ohkubo H, Shimomura Y, Mukouda I, Sugio K, Kiritani M 2003 Mater. Sci. Eng. A 350 30
Google Scholar
[48] 杨彪, 郑百林, 胡兴健, 贺鹏飞, 岳珠峰 2016 金属学报 52 129
Google Scholar
Yang B, Zheng B L, Hu X J, He P F, Yue Z F 2016 Acta Metall. Sin. 52 129
Google Scholar
DownLoad:
Catalog
Metrics
- Abstract views: 9569
- PDF Downloads: 108
- Cited By: 0
