-
将液滴沉积在高于Leidenfrost温度的表面上, 液滴将悬浮在自身的蒸汽垫上, 这使液滴具有惊人的移动性, 通常通过构造不对称的微纳结构表面对液滴下方的蒸汽流进行校正, 实现液滴自驱动. 但液滴运动方向和液滴输运速度(10—40 cm/s)具有局限性. 本实验构造Leidenfrost传热面和撞击面, Leidenfrost传热面用于悬浮液滴并为其提供足够的能量, 当Leidenfrsot液滴(燃料)与撞击面(点火器)接触时, 粗糙环的大量微/纳米腔不仅会向液滴产生额外的辐射热量, 而且还会提供成核点以在约10 ms内触发爆炸沸腾. 利用周期性爆炸沸腾产生的脉冲推力Fth实现液滴自驱动. 液滴运动初始阶段由于惯性力Fi占主导, 液滴撞击多为镜面反射, 液滴运动轨迹较为混乱, 随着液滴直径减小, 脉冲推力Fth占主导, 液滴轨迹通过Leidenfrost传热面中心. 同时液滴输运速度高达68.91 cm/s, 这是在以往微纳结构表面液滴自驱动从未实现的. 这一发现为高温下操纵液滴提供了新的思路, 有望在微流控和传热等两相系统中得到重要的应用.
-
关键词:
- Leidenfrost /
- 液滴动力学 /
- 爆炸沸腾 /
- 热量传递
When a droplet is placed on a surface with a temperature higher than Leidenfrost temperature, it will be levitated on its own vapor cushion, which makes the droplet have amazing mobility. Generally, the vapor flow under the droplet is corrected by constructing asymmetry micro/nano textured surfaces to realize the self-propulsion of the droplet. However, the control of droplet dynamics becomes uncertain due to the complicated interaction among liquid-vapor-solid phases, and the direction of droplet motion and droplet transport velocity (10－40 cm/s) have limitations. Leidenfrost heat transfer surface and impact surface are constructed in this experiment. When the surface of Leidenfrost heat transfer for droplet levitation contacts the droplet which the sufficient energy flows towards, the rough ring surface acts as an igniter. When a warm Leidenfrsot droplet (fuel) contacts skirt ring (igniter), abundant micro/nano cavities of rough skirt ring not only generate additional radiation heat flux towards droplet but also provide nucleation sites to trigger explosive boiling on a ～10 ms time scale. The thrust force Fth generated by periodic explosive boiling realizes the self-propulsion of droplets. In the initial stage of droplet motion, the inertial force Fi is dominant, and the droplet impact is mostly specular reflection, and the droplet trajectory is chaotic. With the decrease of droplet diameter, the pulsed thrust Fth is dominant, and the droplet trajectory passes through the center of the Leidenfrost heat transfer surface. Our experimental results show that the droplet passes through the center of the Leidenfrost heat transfer surface in a wide diameter range (D = 0.671－1.576 mm). For the last (150th) collision with the rough ring, the curved trajectory exists instead of line trajectory with$ D \sim 0.105 $ mm. For a very small droplet, the drag force Fd is dominant, which prevents the droplet from continuing to move. The droplet is followed by sessile droplet evaporation until it totally disappears. At the same time, the droplet transport velocity is as high as 68.91 cm/s, which has not been realized before. The present work provides a new method to manipulate droplet motion at a high temperature. Our Leidenfrost system is simple, cost-effective and lasts long-term operation because it does not depend on complicated micro/nano fabrications, which is expected to be used in microfluidic and heat transfer two-phase systems.-
Keywords:
- Leidenfrost /
- droplet dynamics /
- explosive boiling /
- heat transfer
[1] Leidenfrost J G 1966 Int. J. Heat Mass Transfer 9 1153
Google Scholar
[2] Vakarelski I U, Marston J O, Chan D Y, Thoroddsen S T 2011 Phys. Rev. Lett. 106 214501
Google Scholar
[3] Sengupta S, Patra D, Ortiz-Rivera I, Agrawal A, Shklyaev S, Dey K K, Cordova-Figueroa U, Mallouk T E, Sen A 2014 Nat. Chem. 6 415
Google Scholar
[4] Baylis J R, Yeon J H, Thomson M H, Kazerooni A, Wang X, John A E S, Lim E B, Chien D, Lee A, Zhang J Q 2015 Sci. Adv. 1 e1500379
Google Scholar
[5] Dittrich P S, Manz A 2006 Nat. Rev. Drug discovery 5 210
Google Scholar
[6] Chen M Y, Jia Z H, Zhang T, Fei Y Y 2018 Appl. Surf. Sci. 433 336
Google Scholar
[7] Chu F, Luo J, Hao C, Zhang J, Wu X, Wen D 2020 Langmuir 36 5855
Google Scholar
[8] 王宏, 廖强, 朱恂 2007 化工学报 58 2313
Google Scholar
Wang H, Liao Q, Zhu X 2007 J. Chem. Ind. Eng. 58 2313
Google Scholar
[9] Li J, Hou Y, Liu Y, Hao C, Li M, Chaudhury M K, Yao S, Wang Z 2016 Nat. Phys. 12 606
Google Scholar
[10] Sobac B, Rednikov A, Dorbolo S, Colinet P 2017 Phys. Fluids 29 082101
Google Scholar
[11] Linke H, Aleman B J, Melling L D, Taormina M J, Francis M J, Dow-Hygelund C C, Narayanan V, Taylor R P, Stout A 2006 Phys. Rev. Lett. 96 154502
Google Scholar
[12] Quéré D 2013 Annu. Rev. Fluid Mech. 45 197
Google Scholar
[13] Scriven L, Sternling C 1960 Nature 187 186
Google Scholar
[14] Jia Z H, Chen M Y, Zhu H T 2017 Appl. Phys. Lett. 110 091603
Google Scholar
[15] Lagubeau G, Le Merrer M, Clanet C, Quéré D 2011 Nat. Phys. 7 395
Google Scholar
[16] Wang B, Xu J L, Zhang W, Li Y X 2011 Sens. Actuators, A 169 194
Google Scholar
[17] Xu J, Zhang W 2008 Int. J. Heat Mass Transfer 51 389
Google Scholar
[18] Lyu S, Mathai V, Wang Y, Sobac B, Colinet P, Lohse D, Sun C 2019 Sci. Adv. 5 eaav8081
Google Scholar
[19] Ok J T, Lopez-Oña E, Nikitopoulos D E, Wong H, Park S 2010 Microfluid. Nanofluid. 10 1045
[20] Grounds A, Still R, Takashina K 2012 Sci. Rep. 2 720
Google Scholar
[21] Shahriari A, Wilson P S, Bahadur V 2018 Phys. Rev. E 98 013103
Google Scholar
[22] Cole R 1974 Adv. Heat Transfer 10 85
Google Scholar
[23] Kandlikar S G 2004 J. Heat Transfer 126 8
Google Scholar
[24] Kandlikar S G 2020 J. Heat Transfer 142 100801
Google Scholar
[25] Zhu B, Xu J, Yan C, Xie J 2020 Int. J. Heat Mass Transfer 148 119080
[26] 张海松, 朱鑫杰, 朱兵国, 徐进良, 刘欢 2020 物理学报 69 064401
Google Scholar
Zhang H S, Zhu X J, Zhu B G, Xu J L, Liu H 2020 Acta Phys. Sin. 69 064401
Google Scholar
[27] Shati A K A, Blakey S G, Beck S B M 2011 Energy Build. 43 400
Google Scholar
[28] Yan X, Xu J, Meng Z, Xie J, Wang H 2020 Small 16 e2001548
Google Scholar
[29] Ishii M, Zuber N 1979 AIChE J. 25 843
Google Scholar
-
图 1 爆炸沸腾触发液滴自驱动的新方法
Fig. 1. A new method of explosive boiling to trigger the self-propulsion of droplet.
图 2 (a)实验装置图. 1, 紫铜环; 2, 黄铜加热块; 3, 加热棒; 4, 不锈钢底座; 5, 调压器; 6, 继电器; 7, PID温控仪; 8, K型热电偶; 9, 麦克风; 10, 高速数据采集仪(ScopeCorder DL750); 11, 同步器(MotionPro Timing Hub); 12, 高速相机(MotionPro Y4, IDT); 13, 微注射泵(RSP01-BDG); 14, 安捷伦34970A. (b) 黄铜加热块和紫铜环尺寸 (单位: mm)
Fig. 2. (a) Experimental setup. 1, copper skirt ring; 2, brass heating block; 3, cartridge heater; 4, stainless steel base; 5, voltage transformer; 6, electric relay; 7, PID temperature controller; 8, K thermocouple; 9, microphone; 10, high speed data acquisition system (ScopeCorder DL750; 11, synchronizer (MotionPro Timing Hub); 12, high speed camera (MotionPro Y4, IDT); 13, micro-syringe pump (RSP01-BDG); 14, Agilent 34970A. (b) Brass heating block and copper ring size (all dimensions are in mm).
图 3 采用与两个圆环样品相同的制造技术制备的两个平表面的表征 (a)抛光紫铜表面的扫描电子显微镜图像和接触角; (b)粗糙紫铜表面的扫描电子显微镜图像和接触角; (c), (d)抛光紫铜表面的表面形貌测量; (e), (f) 粗糙紫铜表面的表面形貌测量
Fig. 3. Characterization of two flat surfaces having the same fabrication technique as two skirt ring samples: (a) Scanning electronic microscope (ESEM) image and contact angles for polished copper surface; (b) ESME image and contact angles for rough copper surface; (c), (d) surface morphology measured for smooth copper surface; (e), (f) surface morphology measured for rough copper surface
图 4 液滴整个寿命周期内液滴运动轨迹 (a)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 液滴在粗糙环的运动轨迹; (b)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 液滴在抛光环的运动轨迹; (c)在Tw = 304.5 ℃, Tr = 256.3 ℃下, 液滴在粗糙环的运动轨迹
Fig. 4. Droplet trajectory during the whole droplet lifetime: (a) Droplet trajectory on rough ring at Tw = 223.0 ℃, Tr = 191.4 ℃; (b) droplet trajectory on polished ring at Tw = 223.0 ℃, Tr = 191.4 ℃; (c) droplet trajectory on rough ring at Tw = 304.5 ℃, Tr = 256.3 ℃.
图 5 液滴整个寿命周期内液滴撞击频率 (a)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 粗糙环; (b)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 抛光环; (c) Tw = 304.5 ℃, Tr = 256.3 ℃下, 粗糙环
Fig. 5. Droplet collision frequency during the whole droplet lifetime: (a) Tw = 223.0 ℃, Tr = 191.4 ℃, rough ring; (b) Tw = 223.0 ℃, Tr = 191.4 ℃, polished ring; (c) Tw = 304.5 ℃, Tr = 256.3 ℃, rough ring.
图 7 液滴整个寿命周期内液滴的声音信号 (a)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 粗糙环; (b)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 抛光环; (c) Tw = 304.5 ℃, Tr = 256.3 ℃下, 粗糙环
Fig. 7. Droplet sound voltage during the whole droplet lifetime: (a) Tw = 223.0 ℃, Tr = 191.4 ℃, rough ring; (b) Tw = 223.0 ℃, Tr = 191.4 ℃, polished ring; (c) Tw = 304.5 ℃, Tr = 256.3 ℃, rough ring.
图 6 液滴整个寿命周期内液滴运动速度 (a) 在Tw = 223.0 ℃, Tr = 191.4 ℃下, 粗糙环; (b)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 抛光环; (c) Tw = 304.5 ℃, Tr = 256.3 ℃下, 粗糙环
Fig. 6. Droplet traveling velocity during the whole droplet lifetime: (a) Tw = 223.0 ℃, Tr = 191.4 ℃, rough ring; (b) Tw = 223.0 ℃, Tr = 191.4 ℃, polished ring; (c) Tw = 304.5 ℃, Tr = 256.3 ℃, rough ring.
图 8 液滴撞击瞬间 (a)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 粗糙环; (b)在Tw = 223.0 ℃, Tr = 191.4 ℃下, 抛光环; (c) Tw = 304.5 ℃, Tr = 256.3 ℃下, 粗糙环; (d)液滴内汽泡运动机理
Fig. 8. Droplet impact moment: (a) Tw = 223.0 ℃, Tr = 191.4 ℃, rough ring; (b) Tw = 223.0 ℃, Tr = 191.4 ℃, polished ring; (c) Tw = 304.5 ℃, Tr = 256.3 ℃, rough ring; (d) movement mechanism of bubble in droplets.
-
[1] Leidenfrost J G 1966 Int. J. Heat Mass Transfer 9 1153
Google Scholar
[2] Vakarelski I U, Marston J O, Chan D Y, Thoroddsen S T 2011 Phys. Rev. Lett. 106 214501
Google Scholar
[3] Sengupta S, Patra D, Ortiz-Rivera I, Agrawal A, Shklyaev S, Dey K K, Cordova-Figueroa U, Mallouk T E, Sen A 2014 Nat. Chem. 6 415
Google Scholar
[4] Baylis J R, Yeon J H, Thomson M H, Kazerooni A, Wang X, John A E S, Lim E B, Chien D, Lee A, Zhang J Q 2015 Sci. Adv. 1 e1500379
Google Scholar
[5] Dittrich P S, Manz A 2006 Nat. Rev. Drug discovery 5 210
Google Scholar
[6] Chen M Y, Jia Z H, Zhang T, Fei Y Y 2018 Appl. Surf. Sci. 433 336
Google Scholar
[7] Chu F, Luo J, Hao C, Zhang J, Wu X, Wen D 2020 Langmuir 36 5855
Google Scholar
[8] 王宏, 廖强, 朱恂 2007 化工学报 58 2313
Google Scholar
Wang H, Liao Q, Zhu X 2007 J. Chem. Ind. Eng. 58 2313
Google Scholar
[9] Li J, Hou Y, Liu Y, Hao C, Li M, Chaudhury M K, Yao S, Wang Z 2016 Nat. Phys. 12 606
Google Scholar
[10] Sobac B, Rednikov A, Dorbolo S, Colinet P 2017 Phys. Fluids 29 082101
Google Scholar
[11] Linke H, Aleman B J, Melling L D, Taormina M J, Francis M J, Dow-Hygelund C C, Narayanan V, Taylor R P, Stout A 2006 Phys. Rev. Lett. 96 154502
Google Scholar
[12] Quéré D 2013 Annu. Rev. Fluid Mech. 45 197
Google Scholar
[13] Scriven L, Sternling C 1960 Nature 187 186
Google Scholar
[14] Jia Z H, Chen M Y, Zhu H T 2017 Appl. Phys. Lett. 110 091603
Google Scholar
[15] Lagubeau G, Le Merrer M, Clanet C, Quéré D 2011 Nat. Phys. 7 395
Google Scholar
[16] Wang B, Xu J L, Zhang W, Li Y X 2011 Sens. Actuators, A 169 194
Google Scholar
[17] Xu J, Zhang W 2008 Int. J. Heat Mass Transfer 51 389
Google Scholar
[18] Lyu S, Mathai V, Wang Y, Sobac B, Colinet P, Lohse D, Sun C 2019 Sci. Adv. 5 eaav8081
Google Scholar
[19] Ok J T, Lopez-Oña E, Nikitopoulos D E, Wong H, Park S 2010 Microfluid. Nanofluid. 10 1045
[20] Grounds A, Still R, Takashina K 2012 Sci. Rep. 2 720
Google Scholar
[21] Shahriari A, Wilson P S, Bahadur V 2018 Phys. Rev. E 98 013103
Google Scholar
[22] Cole R 1974 Adv. Heat Transfer 10 85
Google Scholar
[23] Kandlikar S G 2004 J. Heat Transfer 126 8
Google Scholar
[24] Kandlikar S G 2020 J. Heat Transfer 142 100801
Google Scholar
[25] Zhu B, Xu J, Yan C, Xie J 2020 Int. J. Heat Mass Transfer 148 119080
[26] 张海松, 朱鑫杰, 朱兵国, 徐进良, 刘欢 2020 物理学报 69 064401
Google Scholar
Zhang H S, Zhu X J, Zhu B G, Xu J L, Liu H 2020 Acta Phys. Sin. 69 064401
Google Scholar
[27] Shati A K A, Blakey S G, Beck S B M 2011 Energy Build. 43 400
Google Scholar
[28] Yan X, Xu J, Meng Z, Xie J, Wang H 2020 Small 16 e2001548
Google Scholar
[29] Ishii M, Zuber N 1979 AIChE J. 25 843
Google Scholar
下载:
计量
- 文章访问数: 5384
- PDF下载量: 108
- 被引次数: 0
