搜索

x

留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

钼掺杂γ-U (100)表面上H2分子解离、H原子和O原子扩散的第一性原理研究

李俊炜 贾维敏 魏雅璇 吕沙沙 王金涛 李正操

引用本文:
Citation:

钼掺杂γ-U (100)表面上H2分子解离、H原子和O原子扩散的第一性原理研究

李俊炜, 贾维敏, 魏雅璇, 吕沙沙, 王金涛, 李正操

First principles study of H2 dissociation, H atom and O atom diffusion on Mo doped γ-U (100) surface

Li Jun-Wei, Jia Wei-Min, Wei Ya-Xuan, Lü Sha-Sha, Wang Jin-Tao, Li Zheng-Cao
PDF
HTML
导出引用
  • 铀钼合金在贮存、运输等过程中, 易受到小分子的表面腐蚀作用, 其中影响最大的是氢蚀和氧化作用. 为进一步探究该反应机理, 基于密度泛函理论和过渡态计算程序, 本文开展了H2分子在Mo原子掺杂和Mo涂层γ-U (100)的解离吸附, H和O原子在上述表面的表面扩散、体相扩散的第一性原理研究. 主要计算了H2分子在上述表面解离的最小能量路径; 开展了H和O原子在最稳定吸附位点间扩散的过渡态研究; 分析了H和O原子体相扩散中吸附能与吸附高度的联系. 研究结果表明, 当H2分子在顶位平行吸附后, 需跨越能量势垒, 诱发H—H键断裂, 之后体系能量降低, 两个氢原子与近邻原子成键, 稳定吸附在表面的桥位, 同时H2在Mo涂层表面解离所需能垒高于Mo原子掺杂表面; O原子在Mo-U表面扩散所需的能垒较低, 能够在铀钼合金表面迅速吸附、解离、扩散, 进而在表面形成氧化膜; H原子和O原子向体相内扩散首先均需要跨越能垒, 进而与体相原子形成化学键, 最后稳定吸附于体相中. 本文利用理论模拟方法, 较为全面地分析了铀钼合金氢蚀和氧化初始阶段的相关机理, 完备了小分子在铀钼合金表面吸附的研究. 研究结果为从理论上探究铀钼合金表面腐蚀机理奠定基础, 为探究铀钼合金腐蚀老化、预估极端环境和特殊环境下铀钼合金的材料性能提供理论支持, 并为进一步指导铀合金的抗腐蚀研究提供参考和帮助.
    As an important uranium alloy, U-Mo alloy has excellent mechanical properties, structural stability and thermal conductivity, which is an important nuclear reactor fuel and tank armor. However, there exists a serious of fundamental problems of U-Mo alloy which need solving for practical applications. U-Mo alloy is easily subjected to surface corrosion of small molecules including the H2, O2, H2O, and CO2. The hydrogen corrosion and oxidation will have significant influence on it. In order to further investigate the reaction mechanism, based on the density functional theory and the transition state algorithm, the first principles calculation of γ-U (100) with Mo atom doping and Mo coating is carried out.Firstly, the minimum energy path of H2 molecule is calculated for the dissociation adsorption on Mo-U and 4Mo-U surface. Secondly, the transition states of H and O atoms are studied during surface diffusing between adjacent most stable adsorption sites. Thirdly, the bulk phase diffusion of H and O atoms are investigated and the relationship is analyzed between adsorption energy and adsorption height in the bulk phase diffusion.The results show that when H2 molecule is adsorbed at the configuration of top horizontal position, the H atom needs to overcome a barrier to triggering off the H—H bond-broken and then is adsorbed on surface bridge site by the neighboring atoms. The energy barrier for H2 dissociation on 4Mo-U is higher than that of Mo-U. Meanwhile, the lower energy barrier is required for O atom to diffuse in Mo-U, so that it can be adsorbed, dissociated and diffused quickly, and then forming an oxidation film on the surface. Furthermore, both H and O atoms need to cross the energy barrier to diffuse into the body phase, forming chemical bonds with the atoms and staying in the body phase stably finally.In this paper, we comprehensively analyze the dissociation and diffusion of the initial stage for hydrogen corrosion and oxidation on uranium-molybdenum alloy by theoretical studies. The results lay a foundation for theoretically exploring the surface corrosion mechanism of U-Mo alloy. Meanwhile, They provide theoretical support for investigating burn-in and corrosion of uranium-molybdenum alloy, predicting material properties under extreme and special environment, and providing a reference for further research on corrosion resistance of uranium-molybdenum alloy.
      通信作者: 李正操, zcli@tsinghua.edu.cn
    • 基金项目: 国家自然科学基金(批准号: 11975135, 12005017)和国家重点基础研究发展计划(批准号: 2020YFB1901800)资助的课题.
      Corresponding author: Li Zheng-Cao, zcli@tsinghua.edu.cn
    • Funds: Project supported by the National Natural Science Foundation of China (Grant Nos. 11975135, 12005017) and the National Basic Research Program of China (Grant No. 2020YFB1901800).
    [1]

    伯格J. J. 著 (石琪 译) 1983 铀合金物理冶金 (北京: 原子能出版社) 第76—79页

    Burke J J (translated by Shi Q)1983 Physical Metallurgy of Uranium Alloys (Beijing: Atomic Energy Press) pp76–79 (in Chinese)

    [2]

    Yang X Y, Yang Y, Liu Y, Wang Z W, Wärnå J, Xu Z T, Zhang P 2020 Prog. Nucl. Energy 122 103268Google Scholar

    [3]

    Koelling D D, Freeman A J 1973 Phys. Rev. B 7 4454Google Scholar

    [4]

    Shen Z Y, Kong Y, Du Y, Zhang S Y 2021 Calphad 72 102241Google Scholar

    [5]

    SU Q L, DENG H Q, AO B Y, Xiao S F, Chen P H, Hu W Y 2014 Rsc Advances 4 57308Google Scholar

    [6]

    Bajaj S, Landa A, Söderlind P, Turchi P E A, Arróyave R 2011 J. Nucl. Mater. 419 177Google Scholar

    [7]

    Castellano A, Bottin F, Dorado B, Bouchet J 2020 Phys. Rev. B 101 184111Google Scholar

    [8]

    Losada E L, Garces J E 2019 J. Nucl. Mater. 518 380Google Scholar

    [9]

    Alonso P R, Rubiolo G H 2007 Modell. Simul. Mater. Sci. Eng. 15 263Google Scholar

    [10]

    Powell G L, Kirkpatrick J R 1997 J. Alloys Compd. 253 167

    [11]

    Kautz E J, Lambeets S V, Royer J, Perea D E, Harilal S S 2022 Scr. Mater. 212 114528Google Scholar

    [12]

    Ilton E S, Bagus P S 2011 Surf. Interface Anal. 43 1549Google Scholar

    [13]

    Mclean W, Colmenares C A, Smith R L, Somorjai G A 1982 Phys. Rev. B 25 8Google Scholar

    [14]

    Tian X F, Wang Yu, Li L S, Wu M D, Yu Y 2020 Comput. Mater. Sci. 179 109633Google Scholar

    [15]

    Liu G D, Liu Z X, Ao B Y, Hu W Y, Deng H Q 2018 Comput. Mater. Sci. 144 85Google Scholar

    [16]

    李俊炜, 贾维敏, 吕沙沙, 魏雅璇, 李正操, 王金涛 2022 物理学报 71 226601Google Scholar

    Li J W, Jia W M, Lü S S, Wei Y X, Li Z C, Wang J T 2022 Acta Phys. Sin. 71 226601Google Scholar

    [17]

    Kresse G, Furthmüller J 1996 Comput. Mater. Sci. 6 15Google Scholar

    [18]

    Kresse G, Hafner J 1993 Phys. Rev. B: Condens. Matter. 48 13115Google Scholar

    [19]

    Perdew J P, Chevary J A, Vosko S H, Jackson K A, Pederson M R, Singh D J, Fiolhais C 1993 Phys. Rev. B: Condens. Matter. 46 6671

    [20]

    Perdew J P, Burke K, Ernzerhof M 1996 Phys. Rev. Lett. 77 3865Google Scholar

    [21]

    Payne M C, Teter M P, Allan D C, Arias T A, Joannopoulos J D 1992 Rev. Mod. Phys. 64 1045Google Scholar

    [22]

    Henkelman G, Uberuaga B P, Jónsson H 2000 J. Chem. Phys. 113 9901Google Scholar

    [23]

    Pack James D, Monkhorst H J 1976 Phys. Rev. B 13 5188Google Scholar

    [24]

    Chiotti P, Klepfer H H, White R W 1959 Trans. Am. Soc. Metals 51 772

    [25]

    Henkelman G, Arnaldsson A, Jónsson H 2006 Comput. Mater. Sci. 36 354Google Scholar

    [26]

    Electronegativity of Chemical Elements, Material-properties https://material-properties.org/electronegativity-of-chemical-elements/ [2023-1-1]

    [27]

    Deringer V L, Tchougréeff A L, Dronskowski R 2011 J. Phys. Chem. A 115 5461Google Scholar

    [28]

    Nelson R, ErturalC, George J, Deringer V, Dronskowski R 2020 J. Comput. Chem. 41 1931Google Scholar

  • 图 1  H2分子吸附解离示意图 (a) Mo-U; (b) 4Mo-U

    Fig. 1.  Schematic diagram of H2 molecular adsorption and dissociation: (a) Mo-U; (b) 4Mo-U

    图 2  H2分子在Mo-U和4Mo-U表面解离吸附过程的最小能量路径 (a) Mo-U; (b) 4Mo-U

    Fig. 2.  The minimum energy paths (MEPs) for H2 adsorption and dissociation on Mo-U and 4Mo-U surface: (a) Mo-U; (b) 4Mo-U.

    图 3  H2分子在Mo-U表面解离吸附过程中与部分原子的分波态密度 (a) Mo原子和H原子的分波态密度; (b) 13号U原子和H原子的分波态密度

    Fig. 3.  (a) The partial density of states (PDOS) between H and surface atoms at the adsorption and dissociation on Mo-U: (a) PDOS of Mo and H atoms; (b) PDOS of 13 th U and H atoms.

    图 4  H2分子在4Mo-U表面解离吸附过程中部分原子的分波态密度 (a) 3号Mo原子和H原子的分波态密度; (b) 4号Mo原子和H原子的分波态密度

    Fig. 4.  (a) PDOS between H and surface atoms at the adsorption and dissociation on 4Mo-U: (a) PDOS of 3th Mo and H atoms; (b) PDOS of 4th U and H atoms.

    图 5  H2在Mo-U表面解离吸附过程中差分电荷密度(等值面: 0.002 e/Å3) (a) 初态; (b) 过渡态; (c) 终态

    Fig. 5.  Differential charge density of H2 at the adsorption and dissociation on Mo-U (Isosurfaces level: 0.002 e/Å3): (a) Initial state; (b) transition state; (c) final state.

    图 6  H2在4Mo-U表面解离吸附过程中差分电荷密度(等值面: 0.002 e/Å3) (a) 初态; (b) 过渡态; (b) 终态

    Fig. 6.  Differential charge density of H2 at the adsorption and dissociation on 4Mo-U (Isosurfaces level: 0.002 e/Å3): (a) Initial state; (b) transition state; (c) final state.

    图 7  不同能垒下H2分子净电荷转移结果随过渡态能垒的变化, 插图为H2分子Mo-U和4Mo-U解离时的电子态密度

    Fig. 7.  The net charge transfer of H2 molecules versus energy barriers, and the illustration shows PDOS of H2 molecules under transition state on Mo-U and 4Mo-U.

    图 8  (a) H原子在Mo-U表面扩散过程的最小能量路径; (b) H原子在4Mo-U表面扩散过程的最小能量路径

    Fig. 8.  (a) The MEPs for H atom diffusion on Mo-U surface; (b) the MEPs for H atom diffusion on 4Mo-U surface.

    图 9  (a) O原子在Mo-U表面扩散过程的最小能量路径; (b) O原子在4Mo-U表面扩散过程的最小能量路径

    Fig. 9.  (a) The MEPs for O atom diffusion on Mo-U surface; (b) the MEPs for O atom diffusion on 4Mo-U surface.

    图 10  H原子在Mo-U和4Mo-U体内扩散优化前后的俯视图和侧视图 (a) 优化前H-Mo-U_First; (b)优化前H-Mo-U_Second; (c)优化前H-Mo-U_Third; (d)优化前H-4Mo-U_First; (e) 优化前H-4Mo-U_Second; (f) 优化前H-4Mo-U_Third. 下方对应图像为其优化后结果, 如(a')优化后H-Mo-U_First

    Fig. 10.  Top and side views of H atom bulk diffusion on Mo-U surface before and after structure optimization: (a) H-Mo-U_First before optimization; (b) H-Mo-U_Second before optimization; (c) H-Mo-U_Third before optimization; (d) H-4Mo-U_First before optimization; (e) H-4Mo-U_Second before optimization; (f) H-4Mo-U_Third before optimization. The corresponding image below is optimization result, such as (a') H-Mo-U_First after optimization.

    图 11  O原子在Mo-U和4Mo-U体内扩散优化前后的俯视图和侧视图 (a) 优化前O-Mo-U_First; (b)优化前O-Mo-U_Second; (c)优化前O-Mo-U_Third; (d)优化前O-4Mo-U_First; (e) 优化前O-4Mo-U_Second; (f) 优化前O-4Mo-U_Third. 下方对应图像为其优化后结果, 如(a')优化后O-Mo-U_First

    Fig. 11.  Top and side views of O atom bulk diffusion on Mo-U surface before and after structure optimization: (a) O-Mo-U_First before optimization; (b) O-Mo-U_Second before optimization; (c) O-Mo-U_Third before optimization; (d) O-4Mo-U_First before optimization; (e) O-4Mo-U_Second before optimization; (f) O-4Mo-U_Third before optimization. The corresponding image below is optimization result, such as (a') O-Mo-U_First after optimization.

    图 12  不同初始吸附构型下, 原子体相扩散稳定吸附高度及吸附能量变化 (a) H原子在Mo-U体相扩散; (b) H原子在4Mo-U体相扩散; (c) O原子在Mo-U体相扩散; (d) O原子在4Mo-U体相扩散

    Fig. 12.  The adsorption height and energy for atom diffusion in bulk phase under different initial adsorption configurations: (a) H atom diffusion in Mo-U bulk phase; (b) H atom diffusion in 4Mo-U bulk phase; (c) O atom diffusion in Mo-U bulk phase; (d) O atom diffusion in 4Mo-U bulk phase.

    图 13  不同初始吸附构型下, O原子与基底成键原子的COHP (a) O-Mo-U_Second; (b) O-Mo-U_Third; (c) O-4Mo-U_Second; (d) O-4Mo-U_Third

    Fig. 13.  The COHP of O atom bonding to the bulk atoms: (a) O-Mo-U_Second; (b) O-Mo-U_Third; (c) O-4Mo-U_Second; (d) O-4Mo-U_Third.

    表 1  H2分子在Mo-U表面不同解离阶段下的净电荷数

    Table 1.  The net charge number of H2 molecules at different dissociation stages on Mo-U surface.

    ConfigurationH1/eH2/eMo1/eU3/eU8/eU13/e
    Initial0.12770.10320.2662–0.1315–0.3385–0.2727
    Transition0.22180.25520.1256–0.0307–0.2919–0.3678
    020.34420.34420.0495–0.0407–0.3044–0.4325
    030.41790.41770.0034–0.0411–0.2918–0.4775
    Final0.44820.44820.0130–0.0436–0.2637–0.5015
    下载: 导出CSV

    表 2  H2分子在4Mo-U表面不同解离阶段下的净电荷数

    Table 2.  The net charge number of H2 molecules at different dissociation stages on 4Mo-U surface.

    ConfigurationH1/eH2/eMo1/eMo2/eMo3/eMo4/e
    Initial0.02670.03190.27420.24840.24560.1868
    010.10000.10000.26850.23370.20870.1183
    Transition0.20800.20800.25280.20730.13270.0377
    030.29920.29920.25270.20300.0856–0.0345
    040.35290.35290.25180.21580.0399–0.0536
    050.37770.37770.24080.24530.0095–0.0225
    Final0.39260.39260.24800.26320.00770.0043
    下载: 导出CSV

    表 A1  O原子在体相扩散后与Mo-U结构中部分原子的ICOHP

    Table A1.  ICOHP between O atom and partial atoms in Mo-U after bulk phase diffusion.

    Mo-U_ SecondICOHP/eVMo-U_ ThirdICOHP/eV
    Mo1-O11.6431U5-O14.8108
    U5-O14.4165U7-O15.0568
    U8-O12.6392U10-O14.8167
    U10-O14.4180U17-O12.2676
    U17-O12.5125
    下载: 导出CSV

    表 A2  O原子在体相扩散后与4Mo-U结构中部分原子的ICOHP

    Table A2.  ICOHP between O atom and partial atoms in 4Mo-U after bulk phase diffusion.

    4Mo-U_SecondICOHP/eV4Mo-U_ThirdICOHP/eV
    Mo3-O12.4263U8-O13.9520
    Mo4-O11.5266U10-O16.0116
    U8-O15.0490U14-O15.9456
    U16-O15.0493U16-O13.9521
    下载: 导出CSV
  • [1]

    伯格J. J. 著 (石琪 译) 1983 铀合金物理冶金 (北京: 原子能出版社) 第76—79页

    Burke J J (translated by Shi Q)1983 Physical Metallurgy of Uranium Alloys (Beijing: Atomic Energy Press) pp76–79 (in Chinese)

    [2]

    Yang X Y, Yang Y, Liu Y, Wang Z W, Wärnå J, Xu Z T, Zhang P 2020 Prog. Nucl. Energy 122 103268Google Scholar

    [3]

    Koelling D D, Freeman A J 1973 Phys. Rev. B 7 4454Google Scholar

    [4]

    Shen Z Y, Kong Y, Du Y, Zhang S Y 2021 Calphad 72 102241Google Scholar

    [5]

    SU Q L, DENG H Q, AO B Y, Xiao S F, Chen P H, Hu W Y 2014 Rsc Advances 4 57308Google Scholar

    [6]

    Bajaj S, Landa A, Söderlind P, Turchi P E A, Arróyave R 2011 J. Nucl. Mater. 419 177Google Scholar

    [7]

    Castellano A, Bottin F, Dorado B, Bouchet J 2020 Phys. Rev. B 101 184111Google Scholar

    [8]

    Losada E L, Garces J E 2019 J. Nucl. Mater. 518 380Google Scholar

    [9]

    Alonso P R, Rubiolo G H 2007 Modell. Simul. Mater. Sci. Eng. 15 263Google Scholar

    [10]

    Powell G L, Kirkpatrick J R 1997 J. Alloys Compd. 253 167

    [11]

    Kautz E J, Lambeets S V, Royer J, Perea D E, Harilal S S 2022 Scr. Mater. 212 114528Google Scholar

    [12]

    Ilton E S, Bagus P S 2011 Surf. Interface Anal. 43 1549Google Scholar

    [13]

    Mclean W, Colmenares C A, Smith R L, Somorjai G A 1982 Phys. Rev. B 25 8Google Scholar

    [14]

    Tian X F, Wang Yu, Li L S, Wu M D, Yu Y 2020 Comput. Mater. Sci. 179 109633Google Scholar

    [15]

    Liu G D, Liu Z X, Ao B Y, Hu W Y, Deng H Q 2018 Comput. Mater. Sci. 144 85Google Scholar

    [16]

    李俊炜, 贾维敏, 吕沙沙, 魏雅璇, 李正操, 王金涛 2022 物理学报 71 226601Google Scholar

    Li J W, Jia W M, Lü S S, Wei Y X, Li Z C, Wang J T 2022 Acta Phys. Sin. 71 226601Google Scholar

    [17]

    Kresse G, Furthmüller J 1996 Comput. Mater. Sci. 6 15Google Scholar

    [18]

    Kresse G, Hafner J 1993 Phys. Rev. B: Condens. Matter. 48 13115Google Scholar

    [19]

    Perdew J P, Chevary J A, Vosko S H, Jackson K A, Pederson M R, Singh D J, Fiolhais C 1993 Phys. Rev. B: Condens. Matter. 46 6671

    [20]

    Perdew J P, Burke K, Ernzerhof M 1996 Phys. Rev. Lett. 77 3865Google Scholar

    [21]

    Payne M C, Teter M P, Allan D C, Arias T A, Joannopoulos J D 1992 Rev. Mod. Phys. 64 1045Google Scholar

    [22]

    Henkelman G, Uberuaga B P, Jónsson H 2000 J. Chem. Phys. 113 9901Google Scholar

    [23]

    Pack James D, Monkhorst H J 1976 Phys. Rev. B 13 5188Google Scholar

    [24]

    Chiotti P, Klepfer H H, White R W 1959 Trans. Am. Soc. Metals 51 772

    [25]

    Henkelman G, Arnaldsson A, Jónsson H 2006 Comput. Mater. Sci. 36 354Google Scholar

    [26]

    Electronegativity of Chemical Elements, Material-properties https://material-properties.org/electronegativity-of-chemical-elements/ [2023-1-1]

    [27]

    Deringer V L, Tchougréeff A L, Dronskowski R 2011 J. Phys. Chem. A 115 5461Google Scholar

    [28]

    Nelson R, ErturalC, George J, Deringer V, Dronskowski R 2020 J. Comput. Chem. 41 1931Google Scholar

  • [1] 刘续希, 高士森, 喇永孝, 玉栋梁, 柳文波. Zr-2.5Sn合金高温腐蚀过程的相场模拟. 物理学报, 2024, 73(14): 148201. doi: 10.7498/aps.73.20240393
    [2] 杨建宇, 席昆, 竺立哲. 生物大分子过渡态搜索算法及其中的机器学习. 物理学报, 2023, 72(24): 248701. doi: 10.7498/aps.72.20231319
    [3] 董肖. P掺杂LiNH2团簇与LiH反应机理的密度泛函理论研究及一种新储放氢机制. 物理学报, 2023, 72(15): 153101. doi: 10.7498/aps.72.20230374
    [4] 张宇航, 薛振勇, 孙皓, 张珠伟, 陈虎. 酰基辅酶A结合蛋白去折叠动力学的单分子磁镊研究. 物理学报, 2023, 72(15): 158702. doi: 10.7498/aps.72.20230533
    [5] 程超, 王逊, 孙嘉兴, 曹超铭, 马云莉, 刘艳侠. Cr含量对Ti-Nb-Cr合金抗腐蚀性影响的电子结构计算. 物理学报, 2018, 67(19): 197101. doi: 10.7498/aps.67.20180956
    [6] 杨蒙生, 易泰民, 郑凤成, 唐永建, 张林, 杜凯, 李宁, 赵利平, 柯博, 邢丕峰. 沉积态铀薄膜表面氧化的X射线光电子能谱. 物理学报, 2018, 67(2): 027301. doi: 10.7498/aps.67.20172055
    [7] 柯海波, 蒲朕, 张培, 张鹏国, 徐宏扬, 黄火根, 刘天伟, 王英敏. 铀基非晶合金的发展现状. 物理学报, 2017, 66(17): 176104. doi: 10.7498/aps.66.176104
    [8] 孙启响, 闫冰. CH3I2+的二体、三体解离过程的理论研究. 物理学报, 2017, 66(9): 093101. doi: 10.7498/aps.66.093101
    [9] 姚建刚, 宫宝安, 王渊旭. NO在Yn(n=1–12)团簇表面的解离性吸附. 物理学报, 2013, 62(24): 243601. doi: 10.7498/aps.62.243601
    [10] 段永华, 孙勇, 何建洪, 彭明军, 郭中正. Pb-Mg-Al合金腐蚀机理的电子理论研究. 物理学报, 2012, 61(4): 046101. doi: 10.7498/aps.61.046101
    [11] 唐彦丽, 李融武. 二聚物在Cu表面上的扩散和解离研究. 物理学报, 2012, 61(18): 186802. doi: 10.7498/aps.61.186802
    [12] 张辉, 吴迪, 张国英, 肖明珠. 铜基大块非晶合金添加微量元素对腐蚀行为的影响机理研究. 物理学报, 2010, 59(1): 488-493. doi: 10.7498/aps.59.488
    [13] 刘贵立. 镁合金电子结构与腐蚀特性研究. 物理学报, 2010, 59(4): 2708-2713. doi: 10.7498/aps.59.2708
    [14] 刘贵立. 递归法研究Pt对Ti合金腐蚀影响. 物理学报, 2009, 58(5): 3359-3363. doi: 10.7498/aps.58.3359
    [15] 刘贵立. 稀土对镁合金应力腐蚀影响电子理论研究. 物理学报, 2006, 55(12): 6570-6573. doi: 10.7498/aps.55.6570
    [16] 孙强, 谢建军, 张涛. H_2在Ni,Pd与Cu表面的解离吸附. 物理学报, 1995, 44(11): 1805-1813. doi: 10.7498/aps.44.1805
    [17] 陆春明, 李喆深, 董国胜, 任静, 龚雅谦. 化学腐蚀和硫处理对InSb(111)表面的影响. 物理学报, 1992, 41(4): 675-682. doi: 10.7498/aps.41.675
    [18] 高树濬, 钱知强. 均匀合金自扩散的准化学模型. 物理学报, 1965, 21(3): 622-629. doi: 10.7498/aps.21.622
    [19] 谭树松, М.Л.Бернштейн. 钼及钼合金的多边形化的研究. 物理学报, 1964, 20(6): 528-539. doi: 10.7498/aps.20.528
    [20] 刘云旭. 铁—铝—钼—硅合金的脆性研究. 物理学报, 1963, 19(12): 824-829. doi: 10.7498/aps.19.824
计量
  • 文章访问数:  3462
  • PDF下载量:  77
  • 被引次数: 0
出版历程
  • 收稿日期:  2023-01-08
  • 修回日期:  2023-04-27
  • 上网日期:  2023-05-18
  • 刊出日期:  2023-07-20

/

返回文章
返回