惯性约束聚变靶丸内杂质气体抽空流洗过程的数值模拟

邹雄; 漆小波; 张涛先; 高章帆; 黄卫星

doi:10.7498/aps.70.20201491

摘要

低温冷冻靶是实现惯性约束聚变(inertial confinement fusion, ICF)的关键部件之一. 低温靶靶丸内杂质气体的去除程度和效率对低温靶燃料冰层的在线制备具有重要意义. 依据低温靶物理对冰层杂质含量的设计要求, 在计算靶丸内杂质气体最大允许分压的基础上, 建立了靶丸内气体在微米级充气管内流动的抽空流洗模型. 模拟研究了不同微管尺度及结构、温度对靶丸内杂质气体抽空流洗效率的影响规律, 获得了靶丸充气微管的最佳管型设计方案. 基于最佳管型设计, 优化得到了具有最高抽空流洗效率的抽空时间与流洗次数组合策略.

关键词:

Abstract

Cryogenic target is one of the key components of inertial confinement fusion. The removal degree and efficiency of impurity gas in cryogenic target are of great significance to the on-line preparation of ice layer for cryogenic target fuel. According to the design requirements of cryogenic target physics for impurity content in ice layer, the influence factors of upper limit of partial pressure are analyzed, based on the derivation of the calculation formula of maximum allowable partial pressure of impurity gas in the target. Then the flow field of air and hydrogen in microchannels is investigated, and the filling and evacuation model of gas flow in a microscaled filling tube is established. The dynamic simulations of microtubules with different lengths and diameters are carried out. The results show that the microtubules with a length of 5 mm could save 80% of the time compared with the microtubules of 50 mm in length when the microtubule is 5 μm in diameter. At the same time, the total flow washing time decreases by 46% when the diameter of 2 μm is doubled under the condition of 20-mm-long microtubule. Considering the requirements for efficiency and fusion stability, four kinds of tubes are proposed and simulated. The results indicate that the conical transition tube has a strong flow capacity and high flow evacuation efficiency, and is suitable for use as a filling microtubule. On the basis of the best tube shape, the comparison between the two processes under different intermediate pressures is carried out with the time and number of filling and evacuating serving as evaluation criterion. Ultimately, the intermediate pressure of 52000 Pa is selected, the total number of evacuation is 10 and the time is 758 s. Finally, the effect of temperature on the evacuation efficiency is studied in a temperature range of 113 K－293 K in steps of 60 K. The results show that the total time of filling and evacuation will be reduced by 15% on the basis of normal temperature when the temperature is reduced by 60 K, which proves the feasibility of evacuation at low temperature in practical operation.

Keywords:

作者及机构信息

1.
四川大学化学工程学院, 成都　610065

2.
中国工程物理研究院激光聚变研究中心, 绵阳　621900

通信作者: 漆小波, xbqi@caep.cn ; 黄卫星, hwx@scu.edu.cn

Authors and contacts

1.
School of Chemical Engineering, Sichuan University, Chengdu 610065, China

2.
Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900, China

Corresponding author: Qi Xiao-Bo, xbqi@caep.cn ; Huang Wei-Xing, hwx@scu.edu.cn

文章全文 : translate this paragraph

参考文献

[1]	Fanchi J R, Fanchi C J 2016 Energy in the 21st Century (Singapore: World Scientific Publishing Co. Inc.) pp1−23
[2]	Knapp V, Pevec D 2018 Energy Policy 120 94 Google Scholar
[3]	Ongena J, Ogawa Y 2016 Energy Policy 96 770 Google Scholar
[4]	Smalyuk V A, Weber C R, Landen O L, et al. 2019 Plasma Phys. Control Fusion 62 1
[5]	Zheng W G, Wei X F, Zhu Q H, et al. 2017 Matter Radiat. at Extremes 2 243 Google Scholar
[6]	Baton S D, Colaïtis A, Rousseaux C, et al. 2020 High Energy Density Phys. 36 1
[7]	Harding D R, Ulreich J, Wittman M D, et al. 2018 Fusion Sci. Technol. 73 324 Google Scholar
[8]	Yang H, Du K, Lei H L, et al. 2016 J. Fusion Energ. 35 673 Google Scholar
[9]	Aleksandrova I V, Koresheva E R 2019 High Power Laser Sci. 7 1 Google Scholar
[10]	Kozioziemski B J, Mapoles E R, Sater J D, Chernov J D, Moody J D 2011 Fusion Sci. Technol. 59 14 Google Scholar
[11]	Parham T, Kozioziemski B, Atkinson D, et al. 2016 Fusion Sci. Technol. 69 407 Google Scholar
[12]	Bhandarkar S, Parham T, Fair J 2011 Fusion Sci. Technol. 59 51 Google Scholar
[13]	Harding D R, Wittman M D, Edgell D H 2013 Fusion Sci. Technol. 63 95 Google Scholar
[14]	Dongari N, Agrawal A, Agrawal A 2007 Int. J. Heat Mass Tran. 50 3411 Google Scholar
[15]	Stevanovic N D 2007 J Micromech. Microeng. 17 1695 Google Scholar
[16]	Das S K, Tahmouresi F 2016 Int. J. Adv. Math. and Mech. 3 1
[17]	Kurkin E I, Samsonov V N, Shakhov V G 2017 Procedia. Eng. 185 160 Google Scholar
[18]	Simlandi S 2018 Int. J. Eng. Sci. 06 155 Google Scholar
[19]	Yovanovich M M, Khan W A 2016 Int. J. Heat Mass Tran. 93 629 Google Scholar
[20]	Rovenskaya O I 2016 Eur. J. Mech. B-Fluid 59 7 Google Scholar
[21]	Taassob A, Kamali R, Bordbar A 2018 Vacuum 151 197 Google Scholar
[22]	Ahangar E K, Ayani M B, Esfahani J A 2019 Int. J. Mech. Sci. 157-158 802 Google Scholar
[23]	Ahangar E K, Ayani M B, Esfahani J A, Kim K C 2020 Vacuum 173 1
[24]	Edwards M J 2016 J. Phys. Conf. Ser. 688 1 Google Scholar
[25]	Karniadakis G E, Beskok A 2002 Micro Flows: Fundamentals and Simulation (New York: Springer-Verlag) pp1−31
[26]	Prud'Homme R K, Chapman T W, Bowen J R 1986 Appl. Sci. Res. 43 67 Google Scholar
[27]	Tison S A 1993 Vacuum 44 1171 Google Scholar

施引文献

图 1 低温靶靶丸简图

Fig. 1. Schematic of cryogenic target capsule.

下载: 全尺寸图片幻灯片

图 2 靶内温度对杂质气体压力上限的影响

Fig. 2. Influence of temperature in target on upper limit of impurity gas pressure.

下载: 全尺寸图片幻灯片

图 3 气体流域的转换　(a) 空气流域的转换; (b) 氢气流域的转换

Fig. 3. Conversion chart of gas flow field: (a) Conversion chart of air flow field; (b) conversion chart of hydrogen flow field.

下载: 全尺寸图片幻灯片

图 4 低温靶抽空流洗的流程图

Fig. 4. Flow chart of target filling and evacuating.

下载: 全尺寸图片幻灯片

图 5 靶丸抽空流洗物理模型

Fig. 5. The physical model of target filling and evacuating.

下载: 全尺寸图片幻灯片

图 6 模拟结果与计算模型的偏差

Fig. 6. Deviation between simulation and formula.

下载: 全尺寸图片幻灯片

图 7 低温靶内气压与杂质气体分压(残余压力)变化

Fig. 7. Variation of total pressure and residual pressure in cryogenic target capsule.

下载: 全尺寸图片幻灯片

图 8 不同微管长度下残余气压的变化

Fig. 8. Variation of residual pressure at different capillary length.

下载: 全尺寸图片幻灯片

图 9 不同微管长度下单次抽空流洗时间的变化

Fig. 9. Variation of single filling and evacuating time at different capillary length.

下载: 全尺寸图片幻灯片

图 10 不同微管直径下残余气压的变化

Fig. 10. Variation of residual pressure at different capillary diameter.

下载: 全尺寸图片幻灯片

图 11 不同微管直径下单次抽空流洗时间的变化

Fig. 11. Variation of single filling and evacuating at different capillary diameter.

下载: 全尺寸图片幻灯片

图 12 毛细管管型简图

Fig. 12. Schematic of capillary form.

下载: 全尺寸图片幻灯片

图 13 不同微管型式时靶内残余气压的变化

Fig. 13. Variation of residual pressure at different tube type.

下载: 全尺寸图片幻灯片

图 14 最佳流洗中间压力优化

Fig. 14. Optimization of the optimal intermediate pressure of washing.

下载: 全尺寸图片幻灯片

图 15 温度对流洗时间的影响

Fig. 15. Influence of temperature on total filling and evacuating time.

下载: 全尺寸图片幻灯片

[1]	Fanchi J R, Fanchi C J 2016 Energy in the 21st Century (Singapore: World Scientific Publishing Co. Inc.) pp1−23
[2]	Knapp V, Pevec D 2018 Energy Policy 120 94 Google Scholar
[3]	Ongena J, Ogawa Y 2016 Energy Policy 96 770 Google Scholar
[4]	Smalyuk V A, Weber C R, Landen O L, et al. 2019 Plasma Phys. Control Fusion 62 1
[5]	Zheng W G, Wei X F, Zhu Q H, et al. 2017 Matter Radiat. at Extremes 2 243 Google Scholar
[6]	Baton S D, Colaïtis A, Rousseaux C, et al. 2020 High Energy Density Phys. 36 1
[7]	Harding D R, Ulreich J, Wittman M D, et al. 2018 Fusion Sci. Technol. 73 324 Google Scholar
[8]	Yang H, Du K, Lei H L, et al. 2016 J. Fusion Energ. 35 673 Google Scholar
[9]	Aleksandrova I V, Koresheva E R 2019 High Power Laser Sci. 7 1 Google Scholar
[10]	Kozioziemski B J, Mapoles E R, Sater J D, Chernov J D, Moody J D 2011 Fusion Sci. Technol. 59 14 Google Scholar
[11]	Parham T, Kozioziemski B, Atkinson D, et al. 2016 Fusion Sci. Technol. 69 407 Google Scholar
[12]	Bhandarkar S, Parham T, Fair J 2011 Fusion Sci. Technol. 59 51 Google Scholar
[13]	Harding D R, Wittman M D, Edgell D H 2013 Fusion Sci. Technol. 63 95 Google Scholar
[14]	Dongari N, Agrawal A, Agrawal A 2007 Int. J. Heat Mass Tran. 50 3411 Google Scholar
[15]	Stevanovic N D 2007 J Micromech. Microeng. 17 1695 Google Scholar
[16]	Das S K, Tahmouresi F 2016 Int. J. Adv. Math. and Mech. 3 1
[17]	Kurkin E I, Samsonov V N, Shakhov V G 2017 Procedia. Eng. 185 160 Google Scholar
[18]	Simlandi S 2018 Int. J. Eng. Sci. 06 155 Google Scholar
[19]	Yovanovich M M, Khan W A 2016 Int. J. Heat Mass Tran. 93 629 Google Scholar
[20]	Rovenskaya O I 2016 Eur. J. Mech. B-Fluid 59 7 Google Scholar
[21]	Taassob A, Kamali R, Bordbar A 2018 Vacuum 151 197 Google Scholar
[22]	Ahangar E K, Ayani M B, Esfahani J A 2019 Int. J. Mech. Sci. 157-158 802 Google Scholar
[23]	Ahangar E K, Ayani M B, Esfahani J A, Kim K C 2020 Vacuum 173 1
[24]	Edwards M J 2016 J. Phys. Conf. Ser. 688 1 Google Scholar
[25]	Karniadakis G E, Beskok A 2002 Micro Flows: Fundamentals and Simulation (New York: Springer-Verlag) pp1−31
[26]	Prud'Homme R K, Chapman T W, Bowen J R 1986 Appl. Sci. Res. 43 67 Google Scholar
[27]	Tison S A 1993 Vacuum 44 1171 Google Scholar

[1]	万兵兵, 胡伟波, 李晓虎, 黄文锋, 陈坚强, 涂国华. 高速钝锥对不同类型来流扰动的三维感受性. 物理学报, 2024, 73(23): 234701. doi: 10.7498/aps.73.20241383
[2]	李天成, 章晓海, 盛正卯. 激光入射双层等离子体靶产生的表面等离子体波及应用. 物理学报, 2023, 72(4): 045201. doi: 10.7498/aps.72.20221305
[3]	郭富城, 李翠, 厉彦忠. 定向红外光空间分布误差对冷冻靶温度场的影响分析. 物理学报, 2022, 71(11): 110702. doi: 10.7498/aps.71.20212351
[4]	刘博, 邢朴, 丁松, 谢明军, 冯林, 时晓天. 一种新的可计算可压缩流动的预处理方法. 物理学报, 2022, 71(12): 124701. doi: 10.7498/aps.71.20220102
[5]	于家成, 仲佳勇, 安维明, 平永利. 短脉冲强激光驱动磁重联过程的靶后电势分布特征. 物理学报, 2021, 70(6): 065201. doi: 10.7498/aps.70.20201339
[6]	陈国华, 石科军, 储进科, 吴昊, 周池楼, 肖舒. 环形磁场金属等离子体源冷却流场的数值模拟与优化. 物理学报, 2021, 70(7): 075203. doi: 10.7498/aps.70.20201368
[7]	叶欣, 单彦广. 疏水表面振动液滴模态演化与流场结构的数值模拟. 物理学报, 2021, 70(14): 144701. doi: 10.7498/aps.70.20210161
[8]	郭富城, 李翠, 厉彦忠. 定向红外条件下光纤布置形式及光源参数对低温靶温度场的影响. 物理学报, 2021, 70(16): 160703. doi: 10.7498/aps.70.20210029
[9]	刘彪, 周晓凡, 陈刚, 贾锁堂. 交错跃迁Hofstadter梯子的量子流相. 物理学报, 2020, 69(8): 080501. doi: 10.7498/aps.69.20191964
[10]	闫晨帅, 徐进良. 超临界压力CO₂在水平圆管内流动传热数值分析. 物理学报, 2020, 69(4): 044401. doi: 10.7498/aps.69.20191513
[11]	左娟莉, 杨泓, 魏炳乾, 侯精明, 张凯. 气力提升系统气液两相流数值模拟分析. 物理学报, 2020, 69(6): 064705. doi: 10.7498/aps.69.20191755
[12]	喻明浩. 非平衡感应耦合等离子体流场与电磁场作用机理的数值模拟. 物理学报, 2019, 68(18): 185202. doi: 10.7498/aps.68.20190865
[13]	于博, 张岩, 贺伟国, 杭观荣, 康小录, 赵青. 超声波电喷推力器羽流中和特性研究. 物理学报, 2018, 67(4): 040201. doi: 10.7498/aps.67.20171972
[14]	聂涛, 刘伟强. 高超声速飞行器前缘流固耦合计算方法研究. 物理学报, 2012, 61(18): 184401. doi: 10.7498/aps.61.184401
[15]	靳冬欢, 刘文广, 陈星, 陆启生, 赵伊君. 三股互击式喷注器及燃烧室流场的数值模拟. 物理学报, 2012, 61(6): 064206. doi: 10.7498/aps.61.064206
[16]	王蓬, 田修波, 汪志健, 巩春志, 杨士勤. 有限尺寸方靶等离子体离子注入动力学的三维粒子模拟研究. 物理学报, 2011, 60(8): 085206. doi: 10.7498/aps.60.085206
[17]	朱昌盛, 王军伟, 王智平, 冯力. 受迫流动下的枝晶生长相场法模拟研究. 物理学报, 2010, 59(10): 7417-7423. doi: 10.7498/aps.59.7417
[18]	王晓南, 邸洪双, 梁冰洁, 夏小明. 热连轧粗轧调宽轧制过程边角部金属流动三维数值模拟. 物理学报, 2009, 58(13): 84-S88. doi: 10.7498/aps.58.84
[19]	胡　旻, 祝大军, 刘盛纲. 强流相对论电子束双腔纵向自调制研究. 物理学报, 2005, 54(6): 2633-2637. doi: 10.7498/aps.54.2633
[20]	訾炳涛, 姚可夫, 许光明, 崔建忠. 脉冲磁场下金属熔体凝固流场的数值模拟. 物理学报, 2003, 52(1): 115-119. doi: 10.7498/aps.52.115

计量

文章访问数: 4618
PDF下载量: 51
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

搜索

留言板

惯性约束聚变靶丸内杂质气体抽空流洗过程的数值模拟